?     Asked on 6/30/2016by Lonnie Hart

I was sold a Praher TM-12 as a replacement for a Jacuzzi sand filter. Is it correct that the Diverter is to be left off to use this valve?
 Reply

A  Answered on 7/5/2016 by InyoPools Product Specialist Lennox H.

Hi Lonnie, This particular model TM-12-PB valve can not be used with a Jacuzzi sand filter that's why is not fitting properly. If you can provide the model number of your filter or old valve we can locate the correct valve.
 Reply


?     Asked on 5/8/2017by Steve Lissard

old valve is Praher model TM_12. filter is Purex Triton. Will this valve fit?
 Reply

A  Answered on 5/8/2017 by InyoPools Product Specialist Hector F.

The keys A, and B have the compatible valves listed on this parts diagram here.  You would just need to confirm whether you need a side mount, top mount, generic, or a manufacturer model. The 4707P is one of the listed compatible models for the TM12 top mount series.
 Reply


?     Asked on 6/6/2018by Inyo Visitor

My old one only has TM-12 as the model on the label on top around the handle with no letter after the TM-12. It is top-mounted with 1.5 inch pipes. Is this the correct item I need? Actually to save having to unhook piping can I use it to replace the top only by taking the 6 top screws out and put it on mine? Mine is leaking a small amount around the handle and if I do not snap the handle back into the slot snugly I get a drip from my backwash pipe when on filter setting.
 Reply

A  Answered on 6/6/2018 by InyoPools Product Specialist Lennox H.

Hi. I will need to know the tank model in order to confirm if this valve will work because they're different versions of the TM-12 valves. You can replace the Valve Top Assy - E-50-S1B, Diverter Gasket - E12S1 and Cover O-ring - E7S1 to repair your existing valve. 
 Reply


?     Asked on 5/18/2020by Phyllis Smith

I have gotten a spider gasket from you previousIy and have a praher multiport Valve Model TM-12-L that the casing cracked by the pressure gauge. It is on a Ranger Series Sand Filter #54928 I need to know what valve would replace this. I am still using mine as put expoy over the crack but that is starting to deteriorate I think.
 Reply

A  Answered on 5/18/2020 by InyoPools Product Specialist Patrick P.

Hi Phyllis, We would suggest replacing your entire valve with this TM-12-L Valve
 Reply


?     Asked on 1/20/2021by Lynn Kannapinn

Do you sell the rubber gasket that is inside the multiport valve?
 Reply

A  Answered on 1/20/2021 by InyoPools Product Specialist Joe S.

Hello Lynn, we have the PacFab MPV 1.5" Tune Up Kit - APCK1067 for that unit.
 Reply


?     Asked on 11/1/2021by Jonathan

Hi there, I am thinking to replace my PRAHER model TM-12, but it seems the model is out of date. Shall I get the Model TM-12-L, TM-12-PB or any other model to replace the model TM-12? Thank you.

 Reply

A  Answered on 11/1/2021 by InyoPools Product Specialist Patrick P.

Hi Jonathan, Could you send us a few photos of your entire filter? A close of the label on the filter tank, a wide shot of the filter and pump? To supply photos simply click the reply link below and upload your photos. Once we get this information we can make the proper valve recommendation. Thanks so much!
 Reply

  • Commented on 11/1/2021 by Product Owner

    Many thanks for your prompt reply. Here are more photos I took this morning. Hope they can provide you better views of the value and tank.

     Reply

    • Commented on 11/2/2021 by InyoPools Product Specialist Patrick P.

      Hi Jonathan, thanks for the photos! We do not carry the complete Austral sand filter replacement valve. However my suggestion would be to just replace the handle assembly and we do carry the handle assembly for your valve. The parts you would need is this Praher Valve Top Assembly this Praher Spider Gasket and this Spider Gasket Adhesive. This will be the easiest installation without needing to do any re-plumbing. We do have all of these parts in stock ready to ship!
       Reply