Part # 2875
Manufacturer Code 25933-201-000
CMP HydroSeal Pool and Spa Diverter Valve, 2" Inside, 2-1/2" Outside Slip, Gray PVC - 25933-201-000
Features:
I just bought a house with a pool. i'v never had a pool so my question is when the pump comes on automaticaly (it has a timer)what position is the jandy valve supposed to be turned to the main drain or skimmer?
Reply
You can turn the valve so that all the suction is going to the drain at the bottom of the pool, this will suck any dirt or debris on the bottom of the pool through the drain and clean through the filter. If you turn the valve so the suction is going to the skimmer then you will be pulling any leaves or debris off the surface of the pool. You can also set the valve in a half way position so you are pulling from both the skimmer and main drain. I hope this helps.
Reply
Why do the Jandy valves list ID and OD for each valve?
Reply
Each Jandy valve is designed to connect to two different size pipes. For example on a valve shown with ID 1 1/2" and OD 2", a 1 1/2" pipe can be glued inside the port or a 2" pipe can be glued on the outside of the port.
Reply
On Jandy Valve 2875, what is the function of the black knob?
Reply
The black knob on the valve should be filled with marine grease. The knob can be turned to force grease into the valve. This lubricates the valve and helps the handle turn.
Reply
I have this valve installed at my pump. I have a lot of air coming out of the pool jets and it doesn't stop. If I rotate the valve to vacuum and back to skimmer, it clears the air immediately. Do you have any suggestions?
Reply
I would recommend checking the gaskets/o-rings on the valve and pump housing. They may be letting air into the system.
Reply
I have elbows that say 2 on them that connect over the valve. What size valve do I need to order?
Reply
If your elbows fit 2" piping, you will want to buy the diverter valve that is 1 1/2" inside and 2" outside. The 2" elbow will then fit over the outside of the valve port. For lower maintanance you might consider buying the Neverlube version of this valve. They have a Teflon paddle and never have to be lubricated.
Reply
The Most Helpful Review
5 0
(5 out of 5 stars) Jandy Valve
Reviewed By: Krazydoc from Anthony, NM ()
Pros: Eaxctly as described
Cons: None
I needed a replacement for some internal parts and the Inyo Pool price for the ENTIRE valve was less than the total for the indiidual parts!
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Good Valve
Reviewed By: Inyo Customer ()
Really nice valve. Very smooth. Night and day difference from the cheap PVC valves from the hardware store.
Was this review helpful to you?
(5 out of 5 stars) Three way Valve
Reviewed By: Ralph P. from Stuart, Fl ()
Cons: none
Valve is just as in any Pool Supply Store only less expensive...ships and arrives in just three days...and if you are doing an install why not wait and do it right and cheaper...this valve like all Jandy valves can be taken apart to change the configuration of open/close easily...
Was this review helpful to you?
1 0
(5 out of 5 stars) Spa Valve
Reviewed By: Frank Z. from Cave Creek, AZ ()
Used the insides of the new valve to repair the old one. No plumbing required that way. It all work out fine and it was cheaper than buying the individual parts.
Was this review helpful to you?
(5 out of 5 stars) Great 3 Way Valve at a good price
Reviewed By: MikeA from Mesa, AZ ()
Pros: Less expensive than the never lube version and it can be easily lubed
Cons: None
This valve worked great for me and I see no reason to spend more $ to get the never lube version. Other than the grease port, I believe the valves are identical.
Was this review helpful to you?