?     Asked on 1/11/2012by Guest

What is Service Factor?
 Reply

A  Answered on 1/11/2012 by InyoPools Product Specialist Patrick P.

Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
 Reply


?     Asked on 1/12/2012by Guest

Why do I need to purchase a new shaft seal?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
 Reply


?     Asked on 1/12/2012by Guest

Why should I purchase a Tune Up Kit?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
 Reply


?     Asked on 1/11/2015by kenneth garcia

Is the UQC1102 the correct replacement motor for Sta-rite model k48k2pa105c1 1hp Max-E-Glas?
 Reply

A  Answered on 1/12/2015 by InyoPools Product Specialist Robert M.

Hello Kenneth - The UQC1102 would be the correct replacement motor for the K48K2PA105C1 1HP Max-E-Glas.
 Reply


?     Asked on 2/28/2015by Chet

Is the UQC1102 the right motor for a Sta Rite model P2RA5F-182L pump and if so, which tune up kit should I buy with the motor? If not, then which motor and tune up kit would be correct?
 Reply

A  Answered on 3/2/2015 by InyoPools Product Specialist Robert M.

Hello Chet - The correct replacement motor for the P2RA5F-182L is the UQC1152. The tune up kit for Dura-Glas models manufactured before 1998 is GOKIT6. The tune up kit for models manufactured since 1998 is GOKIT54. If your seal plate has a copper cone it is pre 1998. If it does not, you have a 1998-current model.
 Reply


?     Asked on 4/26/2015by Yvette Shuler

Will this motor fit a Flotec AT251001-01 pool pump?
 Reply

A  Answered on 4/27/2015 by InyoPools Product Specialist Andy O.

Yvette- The UQC1102 is the correct motor for your Flotex AT251001. I would also recommend a shaft seal which is part # 5057-07 (37400-0027s).
 Reply


?     Asked on 8/28/2015by Dave

Can I buy the starter capacitor for my 1 hp motor ?
 Reply

A  Answered on 8/31/2015 by InyoPools Product Specialist Lennox H.

Hi Dave, The 124-149 MFD 125V Start Capacitor (BC-124) would be the correct start capacitor for the UQC1102 motor.
 Reply


?     Asked on 8/30/2015by Chin

Are B8241 different in size and ability than UQC1102? I used to have B8241 (56Y). Will that be a problem if I switch to UQC1102 (48Y)? Thanks,
 Reply

A  Answered on 9/2/2015 by InyoPools Product Specialist Lennox H.

Hi Chin, The B2841 is a 1 HP full rated motor which has a total hp of 1.65 and a frame size of 56Y, the UQC1102 is a 1 HP up rated energy efficient motor which has a total hp of 1.25 and a frame size of 48Y. If you currently have the B2841 you would need to change the impeller of the pump and use the motor pad to support the smaller frame size if you want to use the UQC1102. You would also need to make sure that downsizing the motor would not be a problem. 
 Reply


?     Asked on 10/4/2015by joe

What is the correct replacement motor for sta rite maxi glas II 1 hp p4e6e--187L?..in both regular and energy efficient.
 Reply

A  Answered on 10/8/2015 by InyoPools Product Specialist Lennox H.

Hi Joe, The A.O. Smith 1.0 HP Motor Full Rated EE (QC1102) or the A.O. Smith 1 1/2 H.P Square Flange EE Up Rate Motor (UQC1152) would  the correct replacement motors for the Sta-Rite Max Glas II P4E6E-187L Pump.
 Reply


?     Asked on 2/1/2016by terrye

Which motor is the right one for a Flotec AT251501-01
 Reply

A  Answered on 2/2/2016 by InyoPools Product Specialist Andy O.

Terrye- The correct motor for your flotec AT251501-01 would be a Energy Efficient A.O. Smith 1 1/2 H.P Square Flange Up Rate Motor UQC1152. I would also recommend the shaft seal for it which would be 35-423-1096.
 Reply


?     Asked on 2/5/2016by Michael Barbour

What is the correct replacement motor for the Sta Rite Dura Glas pump model # P2RA5E-124L?
 Reply

A  Answered on 2/5/2016 by InyoPools Product Specialist Alex V.

Thank you for your question. You can either use the USQ1102 or the UQC1102 motor. The difference between the 2 motors is that the UQC1102 is more energy efficient. I would also recommend replacing the shaft seal. The P2RA5E-124L has 2 different shaft seals depending on the age of the pump.
 Reply


?     Asked on 2/18/2016by Dave

I have a Sta-Rite P4E6E-151L pump and a Magnetek Century Centurion switchless motor Type 1 Hp. What would be a good replacement unit for these. Thanks, Dave
 Reply

A  Answered on 2/18/2016 by InyoPools Product Specialist Lennox H.

Hi Dave, Base off of the Sta-Rite model # P4E6E-151L, the A.O. Smith 1.0 HP Square Flange EE Full Rate Motor (QC1102) will be the correct replacement motor. I would also recommend getting the Sta-Rite Max-E-Glas II / DuraGlas II Tune Up Kit (GOKIT38).
 Reply


?     Asked on 2/28/2016by Maria

I have a flotec pump the motor is leaking water though the bottom and making some weird noise. I'm wondering could it be the motor.
 Reply

A  Answered on 2/29/2016 by InyoPools Product Specialist Lennox H.

Hi Maria, That is an indication that the shaft seal failed allowing water to leak into the motor. The weird noise that you're hearing is probably the motor bearing failing due to water leaking into the motor. I would recommend replacing the motor along with the shaft seal. If you can provide with the motor CAT or MOD # and the model of the Flotec pump we can locate the correct parts needed.
 Reply


?     Asked on 2/29/2016by Maria

Mod#251001 Flotec
 Reply

A  Answered on 2/29/2016 by InyoPools Product Specialist Andy O.

Maria, The UQC1102 Energy Efficient A.O. Smith 1 H.P Square Flange Up Rate Motor would be the correct motor replacement. You will also need a shaft seal which is 5250-106.
 Reply


?     Asked on 3/8/2016by Paul

I have a Sta-Rite Max-E-Pro with motor model K48K2PA105C1. Would the appropriate replacement pump be the USQ1102 or the UQC1102?
 Reply

A  Answered on 3/9/2016 by InyoPools Product Specialist Lennox H.

Hi Paul, Either motor can work, however I would recommend the full rate (QC1072) motor. I would also recommend getting the Sta-Rite Max-E-Pro Tune Up Kit.
 Reply


?     Asked on 3/9/2016by Joe

Hello, I need to replace my waterfall pump motor model Sta Rite Max-E-Glass II model# P4E6E-187L. I notice when I put this model number in your search feature, it recommends part# UQC1102. When I check the dimensions on the replacement motor it indicated 11" long, my motor is 13". Will this replacement motor still work? Thanks, Joe
 Reply

A  Answered on 3/10/2016 by InyoPools Product Specialist Lennox H.

Hi Joe, Actually the A.O. Smith 1.0 HP Motor Full Rated EE (QC1102) would be the correct replacement motor for the Sta Rite Max-E-Glass II P4E6E-187L pump. I would also recommend getting the Sta-Rite Max-E-Glas II / DuraGlas II Tune Up Kit (GOKIT38).
 Reply


?     Asked on 4/27/2016by Inyo Visitor

I have an eusq1102 motor on a pentair pinnacle . Will this motor work?
 Reply

A  Answered on 4/27/2016 by InyoPools Product Specialist Lennox H.

Hi, This motor will also work as a replacement for the EUSQ1102 motor. I would also recommend that you get the Pentair/Pacfab Pinnacle Tune Up Kit (GOKIT24).
 Reply


?     Asked on 5/3/2016by Michael lukas

i ordered : Energy efficient A.O Smith 1 HP Square Flange Up Rite Motor to replace my burned up Star-rite dura-glas 1 hp ...what tune up kit do i need ?
 Reply

A  Answered on 5/4/2016 by InyoPools Product Specialist Alan M.

Hello Michael, the correct tune up kit for a Sta-Rite Dura Glas pump would be the GOKIT6 for pumps PRE-1998 or the GOKIT54 for pumps 1998-present.
 Reply


?     Asked on 5/22/2016by Inyo Visitor

i have a sta-rite model mpra6e-147L motor. what is the replacement motor? one HP type B max amps 15.3/7.6 9 year old in ground pool. thanks Tony
 Reply

A  Answered on 5/22/2016 by InyoPools Product Specialist Patrick P.

The direct replacement motor for your sta-rite dyna-glas model mpra6e-147L 1 HP pump would be a USQ1102 Replacement Motor. The motor on this page is the energy efficient version of your USQ1102 so by going with the UQC1102 you will be saving roughly 30% on your operational cost. Either way you go you will need a DynaGlas Shaft Seal Kit when you do the replacement.
 Reply


?     Asked on 7/16/2016by thomas clancy

need propeller blade that would go with it. cant get blade off
 Reply

A  Answered on 7/21/2016 by InyoPools Product Specialist Lennox H.

Hi Thomas, We will need to know the model of the pump housing or the part number that's on the impeller in order to locate the replacement.
 Reply


?     Asked on 8/17/2016by Inyo Visitor

What would be the variable speed motor replacement for Flotec pump with motor model number at251001-01, 1hp, 48y frame, motor number c48j2pa105c1
 Reply

A  Answered on 8/20/2016 by InyoPools Product Specialist Lennox H.

Hi, The ECM16SQU VS Motor is the motor that you can use to convert the AT251001-01 pump to a variable speed pump. When replacing the motor we also recommend getting the FloTec Tune Up Kit (GOKIT44).
 Reply


?     Asked on 8/21/2016by Alex

Have the AT 251001-01 pump and need to replace the motor. Mine says Type UAC and this reads UAK. Will this fit? What is the difference? Thanks
 Reply

A  Answered on 8/25/2016 by InyoPools Product Specialist Lennox H.

Hi Alex, The UAC and UAK refer to the capacitor type but this motor will fit the At251001-01 pump.
 Reply


?     Asked on 11/9/2016by Mike Flaherty

I'm trying to replace a 1 hp pump motor made by ao smith part # 7-193221-02. Serial# CA03-01. Do you have a replacement that is compatable?
 Reply

A  Answered on 11/10/2016 by InyoPools Product Specialist Stacey M.

Hello Mike, this motor is for Sta-Rite Max-E-Glas, Max-E-Glas II, Dura-Glas, Dura-Glas II, Dyna-Glas, Dyna-Max Pentair Whisperflow, Pinnacle and Anthony pumps. If you have a Hayward you want to get A.O. Smith 1 HP Energy Efficient Round Flange Up Rate Motor - UCT1102. To get you a pump seal kit we would need to know the type of pump you have which is located on the side of the pump basket.
 Reply


?     Asked on 11/27/2016by Dave D

I'm looking to purchase this motor to replace my USQ1102 motor. What tune up kit do I need? My pump basket doesn't have any name on it. However, there is a partial metal plate attached to the back of the pump that looks like it says Sta-Rite Industries. The number on the plate (the ones I can make out) are 2RA5E-124L. There's s code number 1L92. Thanks.
 Reply

A  Answered on 11/28/2016 by InyoPools Product Specialist Adam Y.

Good morning Dave, This is the Gokit Part # you looking for Tune Up Kit Sta Rite Dura Glas & Max E Glas Pump Pre 1998 - GOKIT6
 Reply


?     Asked on 1/23/2017by Linda Brandt

I want to replace my Sta-Rite Max-E-Glas II motor P4E62E-187L (1hp). Will the energy efficient model UQC1102 work with my existing pump?
 Reply

A  Answered on 1/24/2017 by InyoPools Product Specialist Adam Y.

Good morning Linda, Yes this motor will work. You will also need to replace the shaft seal and o-rings. You can all of them in a kit. The kit is a Gokit38.
 Reply


?     Asked on 2/25/2017by terry

I want to replace my maxi-glass48y 1hp k48l2pa101 pool pump motor will this work
 Reply

A  Answered on 2/27/2017 by InyoPools Product Specialist Andy O.

Hello Terry- Based off the part number you provided (k48l2pa101) the correct motor for your Maxi-glas is the 1.0 HP Full Rate EE Motor (B864SE) - QC1102 and not the Energy Efficient A.O. Smith 1 H.P Square Flange Up Rate Motor - UQC1102. The QC1102 is a Full Rate motor with a total HP of 1.65 whereas the UQC1102 only has a total HP of 1.25. Putting the UQC1102 on your pump without changing the impeller will harm the motor and cause premature failure.
 Reply


?     Asked on 3/29/2017by Gretchen

Hello, I'm looking to replace the capacitor for the motor : STA RITE MODEL P4E6E-151L, I can't seem to locate one. Will this motor work? is it better to replace the whole motor and pump vs. just the capacitor? On a very tight budget & I need to get the pool going. It's been very loud since Sunday. Thank you in advance.
 Reply

A  Answered on 3/29/2017 by InyoPools Product Specialist Lennox H.

Hi, Gretchen. Replacing the capacitor will not fix the problem of a loud motor. When the motor becomes very noisy that's an indicator that the motor bearings are failing. The replacement for your model pump would be the QC1102 motor. If you're unable to replace the entire motor you can get the bearings replace.
 Reply


?     Asked on 6/10/2017by Chris

I need to replace the motor on a Sta-Rite Max-E-Glas II mod. P4E6E-187L, 1HP. Will this work??
 Reply

A  Answered on 6/11/2017 by InyoPools Product Specialist Hector F.

No, the motor replacement that you will need is part number QC1102.
 Reply


?     Asked on 7/5/2017by Inyo Visitor

is this a direct replacement for a USQ1102 ?
 Reply

A  Answered on 7/5/2017 by InyoPools Product Specialist Lennox H.

Hi. Yes, this Century UQC1102 is the energy efficient replacement option to the USQ1102 Motor. 
 Reply


?     Asked on 7/13/2017by Boris Honok

I just purchased a motor. can you ship my new motor wired for 110. ?
 Reply

A  Answered on 7/13/2017 by InyoPools Product Specialist Patrick P.

Unfortunately these come pre-set 230V but there are instructions on how to change to 115V.
 Reply


?     Asked on 7/15/2017by Rob

Hi. I have to replace an AO Smith C48L2PA10504 pump motor. It is rated 1HP, 115/230v 19.2/9.6 amp. 48Y Frame. Square flange Will this motor do the trick? My Square flange measures 5" from bolt center to bolt center.
 Reply

A  Answered on 7/16/2017 by InyoPools Product Specialist Lennox H.

Hi, Rob. The AO Smith C48L2PA10504 motor # cross references to the USQ1152 Motor. You can use either the QC1102 or the UQC1152 motor as a replacement.
 Reply


?     Asked on 7/24/2017by Stan

I have a P4E6E-1871 pump system and need a replacement motor. Will the UQC1102 work as a replacement? Needs to be 5 1/2 in in diameter to work with my frame. Recommendations please...
 Reply

A  Answered on 7/26/2017 by InyoPools Product Specialist Lennox H.

Hi, Stan. The QC1102 is the correct replacement motor for the P4E6E-187L pump. The Max-E-Glas II / DuraGlas II Tune Up Kit - GOKIT38 is the kit needed for that pump.
 Reply


?     Asked on 8/6/2017by Cleve

I currently have a Pentair WF-24. I wondering if I can replace it with a WFE-24? I'd prefer a high efficiency over standard. I see the frame numbers are different. 56Y versus a 48Y.
 Reply

A  Answered on 8/7/2017 by InyoPools Product Specialist Lennox H.

Hi, Cleve. You can use this UCT1102 EE 48Y FR motor or the B661 EE 56Y FR motor as a replacement for the WF-24 pump. The B661 is more energy efficient than this UCT1102 motor. The body diameter is the difference between a 48Y and 56Y frame motor. I would also recommend the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT
 Reply


?     Asked on 9/1/2017by John

Is this the correct replacement for a Flotec AT251001-01, 1HP, SF 1.0, Max amps 13.4/6.7?
 Reply

A  Answered on 9/5/2017 by InyoPools Product Specialist Lennox H.

Hi, John. This UCT1102 motor is the correct replacement for the Flotec AT251001-01 pump. 
 Reply


?     Asked on 9/4/2017by Sally J LaClaire

I need a pump motor and seal kit to replace a floetec AT251001-01 Do you have this in stock. I am in Florida, how long will it take to get here. Thanks
 Reply

A  Answered on 9/6/2017 by InyoPools Product Specialist Lennox H.

Hi, Sally. This UCT1102 motor and the Tune Up Kit - GOKIT44 are the parts you'll need. We do have these items in-stock and would take about 3 business days for delivery with the free shipping option. 
 Reply


?     Asked on 9/25/2017by Dan

Could this replace a STA-Rite MPFA6E-146L 1HP?
 Reply

A  Answered on 9/25/2017 by InyoPools Product Specialist Lennox H.

Hi, Dan. Yes, this UQC1102 motor can be used with the Sta-Rite MPFA6E-146L  pump.
 Reply


?     Asked on 2/19/2018by Maria

Hello. I have a Pentair SF-N1-1A/340038, 1HP, 1.25 S.F. HP that needs a replacement. Looking to change it to an energy efficient motor; would this be the correct replacement? Can you also let me know what other parts I would need in order to replace the motor?
 Reply

A  Answered on 2/19/2018 by InyoPools Product Specialist Hector F.

The closest replacement energy efficient single speed motor would be the B863SE and we highly recommend replacing the seals and gaskets which would be the GOKIT78
 Reply


?     Asked on 7/1/2018by Nick

Need to replace a loud motor, label on motor is faded but the Pump model number is P2RA5E-181L and I have found an online manual where it appears to be a Sta-Rite dura glas pump (though I think the current motor is not the original). The motor model from the manual is A100ELL, Will this energy efficient A.O smith 1 HP up rate motor be an appropriate replacement?
 Reply

A  Answered on 7/1/2018 by InyoPools Product Specialist Lennox H.

Hi, Nick. Yes, this UQC1102 motor will be the energy efficient replacement motor. We recommend that you get the Sta-Rite Dura-Glas 1998 To Present Tune Up Kit - GOKIT54
 Reply


?     Asked on 2/21/2019by Inyo Visitor

I need to replace my pool motor, model number P4E6e-151L. Will this one work?
 Reply

A  Answered on 2/21/2019 by InyoPools Product Specialist Lennox H.

Hi. This UQC1102 motor will NOT work, the QC1102 or the B2841V1 are the correct replacements. The Tune Up Kit for your model pump is Part # GOKIT38.
 Reply


?     Asked on 4/10/2019by shane morris

have pre 1998 Sta-Rite dura glass Max-e-glas main pump model PE-AXE, 124 UL, 12M. It is in an Hot Springs Hot Tub. This looks like best choice for motor. 1) Is that correct? 2) What kit or parts are needed to rebuild/refresh/reseal the pump? Your reply will be greatly appreciated

 Reply

A  Answered on 4/10/2019 by InyoPools Product Specialist Lennox H.

Hi, Shane. Yes, this UQC1102 motor along with the Max-E-Glas Tune Up Kit - GOKIT6 are the parts you will need. 
 Reply


?     Asked on 6/5/2019by Inyo Visitor

Hi there, will this motor replace a Sta-Rite PHK2RA6E - 102L? Pic attached. Many thanks

 Reply

A  Answered on 6/5/2019 by InyoPools Product Specialist Patrick P.

Yes, this motor will replace the motor on a Sta-Rite PHK2RA6E - 102L the diameter of the motor on this UQC1102 is a little narrower than your current motor so you will use the included rubber spacer that comes with the motor. If you don't want to use the rubber spacer and want the same diameter motor that you currently have then you will need the PL2853 1 HP Up Rate 56Y Replacement Motor. You will also need a Sta-Rite SuperMax Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 11/5/2019by Inyo Visitor

will this moter uqc1102 fit my at251001-01 flotec pump
 Reply

A  Answered on 11/5/2019 by InyoPools Product Specialist Lennox H.

Hi. Yes, this UQC1102 motor will fit the Flotec AT251001-01 model pump. 
 Reply


?     Asked on 9/2/2020by Sarth Robert Larkin

Hello, is this the motor I need for a direct replacement? Also, can you please tell me which seal/ring kit I need? Thanks!

 Reply

A  Answered on 12/18/2020 by InyoPools Product Specialist Hector F.

Hi Sarth, the correct single speed replacement motor for the motor included in your photo is the USQ1102. You will also need a Sta-Rite Dura Glas/ Max E Glas seal kit when you replace your motor. Be sure to remove the cone insert that may be in the seal plate when installing the shaft seal. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 11/17/2020by Avery

Will this replace USQ1102?

 Reply

A  Answered on 11/17/2020 by InyoPools Product Specialist Megan C.

Hello Avery, yes you can order the UQC1102 to replace the USQ1102.
 Reply

  • Commented on 11/17/2020 by Product Owner

    Does this come with everything I need for installation or is there another kit that I need to get that has new seals exc...?
     Reply


?     Asked on 5/14/2021by SVH

I'm looking to replace this motor. It died on me this morning. Can you please let me know if your motor is a replacement for it? If not, can you recommend a replacement? Thanks!

 Reply

A  Answered on 5/14/2021 by InyoPools Product Specialist Danny R.

The correct replacement motor for your 168887 pool pump motor is the QC1102.  Here is a link to the proper replacement pool pump motor...Century 1.0 HP Square Flange 48Y Full Rate EE Motor - QC1102
 Reply


?     Asked on 8/7/2021by Billy Chappell

can i replace my USQ 1102 with a energy efficent motor and if so which one?
 Reply

A  Answered on 11/10/2021 by InyoPools Product Specialist Stephen B.

Thank you for Contacting Inyo Pools, V-Green 1.65 HP Square Flange 48Y Variable Speed Motor - ECM16SQU would be an energy efficient replacement
 Reply


?     Asked on 10/16/2024by Jim

Is this motor the correct placement for my Sta-Rite Maxi-Glass-II pool motor. Current one is rated 1 hp. I am not sure if my photos uploaded correctly because when I click on them they disappear

 Reply

A  Answered on 10/16/2024 by InyoPools Product Specialist Rich N.

Hi Jim, it is rated at 1HP but the motor is actually 1.65 total horsepower (see Are All Motors Created Equal? for a full explanation), so the USQ1152 motor is the perfect replacement.  Be sure to get a Tune-Up Kit for your Sta-Rite Maxi-Glass-II pump for a leak-free installation
 Reply