?     Asked on 10/8/2013by Guest

How many hours per day should I run my pump?
 Reply

A  Answered on 10/8/2013 by InyoPools Product Specialist Patrick P.

There are many factors to consider; bather load, gallons of water, pump horsepower, type and size of filter just to name a few. A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals. In peak season, when it is the hottest, raising the run time to 10-12 hours per day will help to keep the pool clean and circulating during it’s time of heaviest use.
 Reply


?     Asked on 10/8/2013by Guest

Can I run my pump without water?
 Reply

A  Answered on 10/8/2013 by InyoPools Product Specialist Patrick P.

Hayward Pool pumps should never operate without water. The pump seal assembly in the pump volute (The area between the strainer basket and the pump motor) protects the pump motor from pool water. This seal assembly gets hot and is cooled by the pool water. If the pump is running without water, the seal will overheat and melt, If left running without water for a long period of time, the heat generated could damage the PVC pipe and other system components.
 Reply


?     Asked on 7/10/2014by Guest

How much is the power consumption difference each hour between 1.5 HP and 1 HP pool pump by KW.
 Reply

A  Answered on 7/10/2014 by InyoPools Product Specialist Patrick P.

A typical 1 HP pump has a power consumption of 1.5 Killowatts per hour (KWH) and a 1.5 HP pump is at about 2.3 KWH
 Reply


?     Asked on 9/26/2014by Guest

I have a Hayward SP1607X10. Is that a previous version of sp2607X10? Will parts for one be the same as parts for the other?
 Reply

A  Answered on 9/26/2014 by InyoPools Product Specialist Patrick P.

You are correct that is the predecessor to the to the sp2607x10. The parts will work for either pump.
 Reply


?     Asked on 1/3/2015by shawn

just want to make sure i am ordering the correct item. my current pump as the model number as SP2607X10 and the serial number as 21120805002046020. its labeled as a hayward pool produtcs item. please advised, thank you.
 Reply

A  Answered on 1/5/2015 by InyoPools Product Specialist Robert M.

Hello Shawn - The Hayward SP2607X10 is the correct replacement pump.
 Reply


?     Asked on 1/29/2015by Patrick

I currently have a 1 HP Pac Fac Pinnacle pump would the 1 HP Hayward Super Pump be a comparable replacement?
 Reply

A  Answered on 1/29/2015 by InyoPools Product Specialist Patrick P.

Hi Patrick - Yes the Hayward 1 HP Super Pump would be a great replacement for the discontinued 1 HP Pac Fab Pinnacle Pump.
 Reply


?     Asked on 5/5/2015by Inyo Visitor

Replacing a Whisperflo WF-26 1.5 hp. Would the SP2607X10 1 hp pump be a good replacement? GPM=45 & Distance to Head=approx. 43' If so, what is the price of the pump with an EE motor?
 Reply

A  Answered on 5/5/2015 by InyoPools Product Specialist Lennox H.

If you don't need the additional .5hp and the 1/2" of pipe size for the in and outlet, the Hayward 1 HP Single Speed Super Pump  will be an option. The  Hayward 1 HP Single Super 2 Pump will be the better replacement. Hayward Super 2 EE Pump 1 HP Single Speed
 Reply


?     Asked on 5/11/2015by Inyo Visitor

We are building a pool... So the dimensions are 24 x 10 and 5 feet deep... What's the best pump please
 Reply

A  Answered on 5/11/2015 by InyoPools Product Specialist Patrick P.

If you do not have any water features likes waterfalls, solar, runs of pipe exceeding 70' or spa jets then I love the 1 HP Hayward Super Pump.
 Reply


?     Asked on 5/18/2015by Lloyd

I am thinking on buying a new pump. I have very little to no suction at that skimmer. I have blown the line and it is not plugged. I have replaced all fittings and valves and still not very good suction. The drain one at the bottom of pool works great. Without skimmer working I can't clean pool. I was wondering if a bigger pump would help. I currently have a 1hp.
 Reply

A  Answered on 5/19/2015 by InyoPools Product Specialist Patrick P.

Lloyd what is the distance of pipe from the pump to the skimmer which is have the bad flow? What is the distance of pipe from the pump to the main drain? Do you know the pipe size for the skimmer line? How about pipe size for the main drain line? What happens when you turn your diverter valve so you shut off the main drain and all of the suction is going to the skimmer?
 Reply


?     Asked on 5/31/2015by Jeff

I need to replace my AO Smith pump C48k2n143b1n, sp-1607-21-m is this the right item?
 Reply

A  Answered on 5/31/2015 by InyoPools Product Specialist Patrick P.

Yes if you were looking to replace the complete pump which includes the pump housing, basket and motor then this would be the correct pump.
 Reply


?     Asked on 6/8/2015by Lora

Hello please help,i have unground pool 16/38 and 8 feet down about 24.000 gallons water, also have sand filter 18'' 150 lb sand,which best pump i need to buy???? Thank you.
 Reply

A  Answered on 6/8/2015 by InyoPools Product Specialist Patrick P.

Hi Lora, As long as this pump will not be powering any water features like waterfalls, solar or spa jets then the 1 HP Hayward Super Pump on this page would be my recommendation.
 Reply


?     Asked on 6/11/2015by Bo Surrell

I have an 18' x 36' in ground pool that is 3' in shallow end of pool and 8' in deep end. I have a Jandy ei salt machine. My flow light will not go off on the salt machine. My current pump is a 1 hp. One of the trouble shooting answers to the Jandy Salt machine says that when the flow light stays on it could be that the pump is not strong enough. Based upon what I have provided do you think I need a 1 1/2 hp pump?
 Reply

A  Answered on 6/11/2015 by InyoPools Product Specialist Patrick P.

Hi Bo, The very first thing I would do is follow the steps in our guide on How to Correct Low Pool Pressure many times these simple steps will fix your flow issue.
 Reply


?     Asked on 6/23/2015by Loyd

What is the overall length
 Reply

A  Answered on 6/23/2015 by InyoPools Product Specialist Dennis R.

Hi Loyd. The overall length of a Hayward Super Pump 1 HP Single Speed is 24".
 Reply


?     Asked on 6/26/2015by Rebecca

How many gallons of water does a Hayward Super Pump, 1 HP self priming, pump per hour?
 Reply

A  Answered on 6/27/2015 by InyoPools Product Specialist Hector F.

Please click here to view the Hayward Super Pump curve.
 Reply


?     Asked on 7/10/2015by Jill Doll

I have an old filter wet institute system in my inground swimming pool 24,000 gallons. I would like to replace this old wet institute with the Hayward system How big of a job is this
 Reply

A  Answered on 7/11/2015 by InyoPools Product Specialist Patrick P.

Hi Jill, the biggest question would be what is the current state of your plumbing, but normally this would be a relatively easy weekend DIY project. We have a good Video on How to Replace a Pool Pump which should give you a better idea of what is involved in this project.
 Reply


?     Asked on 8/16/2015by RICK

My current in ground pool has a pump that plugs into a regular outlet. Do your 3/4hp pumps require a 220 line? Also how about if I go up to a 1hp model?
 Reply

A  Answered on 8/17/2015 by InyoPools Product Specialist Robert M.

Hello Rick - The 3/4HP and 1HP Hayward Super Pumps are dual voltage (115/230).
 Reply


?     Asked on 8/19/2015by Rich

I have a 15k gallon pool with a 60 sqft Hayward DE filter. Thinking of replacing the pump to cut down on the electric bill. Currently, I have a PAC-FAB Challenger 2HP pump. Seems to me the pump and filter are overkill for the size of the pool. Can I use a lower HP pump on the 60 sqft filter? What pump would you suggest?
 Reply

A  Answered on 8/20/2015 by InyoPools Product Specialist Joe S.

Hello Rich, yes you can go with a few different pumps, SP3007X10AZ, or SP3200VSP Offering up to 90% energy cost savings over single-speed pool pump alternatives via an integrated variable-speed drive and totally-enclosed, permanent magnet motor, TriStar VS is an ideal pool upgrade for those looking to reduce energy use and save money.
 Reply


?     Asked on 10/10/2015by Fred Duthie

what is the difference between the single and 2 speed Hayward motor?
 Reply

A  Answered on 10/12/2015 by InyoPools Product Specialist Lennox H.

Hi Fred, A single speed motor runs at 3450 RPM for the desired run time and  a two-speed motor can run at 3450/1725/ RPM for the desired run time.
 Reply


?     Asked on 3/12/2016by Sandy

A cheaper pool pump I've looked at says it shouldn't be exposed to rain/ weather. Can the Hayward pump be completely exposed to the weather??
 Reply

A  Answered on 3/14/2016 by InyoPools Product Specialist Lennox H.

Hi Sandy, This pump can be placed outside exposed to the weather, however it will affect the life span of the pump. The less exposed it is the longer it will last.
 Reply


?     Asked on 3/29/2016by Inyo Visitor

I am getting ready to install a 14x28 foot in ground pool (around 15,000 gallons). The pump is a 1.5 hp with a flow rate of 88 gpm. I need a flow rate of 32 gpm to filter in 8 hrs. The max flow on my 24" filter is 45 gpm. I have 45 feet of head. Based on that a 1 hp pump would supply 50 gpm. Do I really need the 1.5 hp pump? At 42 feet of head it still pumps at 67 GPM. Isn't that to high?
 Reply

A  Answered on 3/29/2016 by InyoPools Product Specialist Scott W.

The 1 HP would work just fine for that size of pool. You definitely need a 1.5 HP though if you start adding features such as, a fountain, a spa, solar heat pump, pool cleaner. Adding any of these features will require more horsepower since the flow rate will be divided up by each addition feature.
 Reply


?     Asked on 3/31/2016by Joel

I am replacing the motor on my SP2607X10 pump. I know I need to replace other items as well. Is there a kit with all the seals & gaskets that I need to replace as well?
 Reply

A  Answered on 4/1/2016 by InyoPools Product Specialist Lennox H.

Hi Joel, The UST1102 is the correct replacement motor and you will also need Hayward Super Pump Tune Up Kit p/n GOKIT3 or GOKIT3SALT depending on what type of sanitizer you use.
 Reply


?     Asked on 4/17/2016by Denny

I have a 18 x 36 in ground pool, 4 ft deep shallow and 8 ft deep. I have a Hayward cartridge filter and 1 1/2 Hayward pool pump. The pump runs on 220 and the motor seems to be very hot. Can't put my hand on it. I go through a pump every 2 years. Any suggestions!!
 Reply

A  Answered on 4/18/2016 by InyoPools Product Specialist Lennox H.

Hi Denny, Several things can cause the motor to run hot, you can check out our Pool Motor Troubleshooting blog for more info.
 Reply


?     Asked on 5/21/2016by Inyo Visitor

I have a 20x40 in ground pool with water jets in the steps. What size pool pump do I need?
 Reply

A  Answered on 5/22/2016 by InyoPools Product Specialist Robert M.

There are several variables that go into selecting the HP of a pool pump. We recommend using our Pump Selection Guide or Video to help you make the correct choice.
 Reply


?     Asked on 5/28/2016by Les

I am replacing old pump with a new one .old was 115v connection. MOVEED black pug from 240 to 115 arrow.connected green wire to green terminal. where does the the white wire and then black wire terminate? there is L1 and L2 does it make a difference?
 Reply

A  Answered on 5/28/2016 by InyoPools Product Specialist Alex V.

Les, If you are wiring for 115v, as long as you have one wire on line 1 and the other on line 2, it will work. This video may help:https://www.inyopools.com/HowToPage/how_to_wire_a_pool_pump.aspx
 Reply


?     Asked on 5/29/2016by Inyo Visitor

Could you give me the RPM for this Hayward Superpump 1 HP
 Reply

A  Answered on 5/29/2016 by InyoPools Product Specialist Matt S.

All single-speed pool pumps should have a motor with 3,450 pumps should have a motor with 3450 RPMs.
 Reply


?     Asked on 7/4/2016by alan scott

i have an 18 by 36 ft pool 8ft to 4 ft depth. how many hours should i run the pump?
 Reply

A  Answered on 7/7/2016 by InyoPools Product Specialist Lennox H.

Hi Alan, Rule of thumb is that the pool pump should run one hour for every 10 degrees of the outside temperature. Or you use our How To: Size a Pool Pump guide to calculate the flow rate to determine the run time.
 Reply


?     Asked on 7/22/2016by Jack

How many GPM is the 1 hp Super Pump?
 Reply

A  Answered on 7/23/2016 by InyoPools Product Specialist Alan M.

This pump has a max of 86 GPM. There is a chart on the product page that shows the GPM based on the feet of head if you have additional.
 Reply


?     Asked on 9/3/2016by Art

I just need the motor.
 Reply

A  Answered on 9/14/2016 by InyoPools Product Specialist Lennox H.

Hi Art.  The UST1102 is the replacement motor for this pump, I will also recommend getting the Hayward Super Pump Tune Up Kit GOKIT3 or GOKIT3SALT.
 Reply


?     Asked on 11/1/2016by clyde

how do you remove the pump from the shaft on the motor
 Reply

A  Answered on 11/1/2016 by InyoPools Product Specialist Scott W.

If it is a Super Pump then the ceramic part you will wedge out with a flat head screwdriver and the spring part of the shaft seal is pulled off of the impeller. Make sure the little rubber washer gets taken off of the impeller as well otherwise the new shaft seal will not slide on to the impeller all the way and it will leak.
 Reply


?     Asked on 1/23/2017by Jay

I don't need the motor just everything else how Can I get it?
 Reply

A  Answered on 1/24/2017 by InyoPools Product Specialist Adam Y.

Good morning Jay, Here is a link to all Hayward Super Pump Parts. If you like that pump Check out the PureLine Prime Pool Pump 1 HP - PL2601.
 Reply


?     Asked on 3/28/2017by Larry

I need a power cord for a Hayward sp2607x10 which has a c48k2n143b1 motor. What's the part number? the only power cords I see are the SPX1250WA and SPX1550WA1. Is either of these compatible?
 Reply

A  Answered on 3/29/2017 by InyoPools Product Specialist Lennox H.

Hi, Larry. If the pump is wired for 115 volts and will plug right into an outlet you can use either power cords depend on whether you have a standard or twist-lock outlet.
 Reply


?     Asked on 5/28/2017by Joe

What is the replacement Super Pump for the Hayward SP1607Z1M 3/4 Super Pump ? I have had this pump for less than three years and the motor seized up and has to be replaced. I cannot find any replacements models for this motor, in fact when i enter the model number in the compatible model box it tells me that model number is not found. What gives ?
 Reply

A  Answered on 5/28/2017 by InyoPools Product Specialist Hector F.

Based on the model number that you have provided this ia a 1 horse power. That Super pump model is SP2607X10. It is possible that you have a 3/4 hp full rated version which is equivalent to this one horse up rated version. Also here is the 3/4 horse power Super pump SP2605X7 but remember that technically this version is a different model hence having less horse power then the model number that you have provided.
 Reply


?     Asked on 6/16/2017by raymond

will this pump be a direct replacement for my existing SP1607Z1M?
 Reply

A  Answered on 6/18/2017 by InyoPools Product Specialist Hector F.

If this motor is mounted specifically to a Hayward Super Pump then yes this would be the direct replacement. You can also look into the Pureline Prime as a drop in replacement.
 Reply


?     Asked on 6/23/2017by mike bell

My pool is 50000 gallons with 120 ft of head i have a 2 hp super pump does this sound like I'm oversized
 Reply

A  Answered on 6/24/2017 by InyoPools Product Specialist Lennox H.

Hi, Mike. You will need to provide us with the FOH on the suction side and the filter model in order to determine if the 2 HP Super Pump is oversized. 
 Reply


?     Asked on 6/23/2017by Inyo Visitor

my 1 hp pump died.will any 1 Hayward 1 hp super pump do the trick .my old one is a Hayward super also.
 Reply

A  Answered on 6/25/2017 by InyoPools Product Specialist Lennox H.

Hi. This Hayward Super Pump 1 HP - SP2607X10 will replace your existing Super Pump.
 Reply


?     Asked on 6/26/2017by Tyson

After buying this, all i will have to do is take out the existing pump/motor then plumb the new pump/motor in and use the previous wiring?
 Reply

A  Answered on 7/23/2017 by InyoPools Product Specialist Alex V.

Tyson, Yes, that is correct, Please note that this is a dual voltage motor and is preset to 230v. If you have 115v, you will need to follow the diagram on the motor to wire it for 115v. 
 Reply


?     Asked on 7/12/2017by Inyo Visitor

If i change from a 1hp to 1.5 hp for 12,000 gal pool, and change from sand to cartridge filter, will it cause a problem?
 Reply

A  Answered on 7/12/2017 by InyoPools Product Specialist Alex V.

Hello, As long as the new filter is sized for the higher horsepower pump, you will not have an issue. 
 Reply


?     Asked on 7/20/2017by Mike

Can I buy the electric end with the impeller there is nothing bad with my housing
 Reply

A  Answered on 7/20/2017 by InyoPools Product Specialist Hector F.

All motor orders come as just the motor. The pump parts have to be assembled to the motor. 
 Reply


?     Asked on 7/20/2017by Mike

Can I buy the electric end with the impeller there is nothing bad with my housing
 Reply

A  Answered on 7/21/2017 by InyoPools Product Specialist Robert M.

Hello Mike - Unfortunately, the motor is not sold with the impeller and other parts assembled. You would have to get each item individually and then put it together. You can find all of the available items on the Hayward Super Pump Parts Page
 Reply


?     Asked on 8/7/2017by Inyo Visitor

will I be able to replace a sta-rite 3/4 hp with this pump with no additional plumbing
 Reply

A  Answered on 8/7/2017 by InyoPools Product Specialist Alex V.

Hello, The ports on both pumps do not line up so re-plumbing will be necessary. 
 Reply


?     Asked on 1/21/2018by FranticGolf

Would this be a match plumbing wise for a Waterway SVL56 1hp pump or would re-plumbing be required?
 Reply

A  Answered on 1/22/2018 by InyoPools Product Specialist Lennox H.

Hi, FranticGolf. You will need to re-plumb if you switch to the Hayward Super Pump. 
 Reply


?     Asked on 4/8/2018by Gene

I am going to need to replace my Hayward SP2807X10 pump. Is the Hayward SP2607X10 a comparable pump for a replacement?
 Reply

A  Answered on 4/9/2018 by InyoPools Product Specialist Patrick P.

Hi Gene, The SP2607X10 a comparable pump for replacing your SP2807X10. However, we would suggest the PL2601 PureLine Prime 1 HP as a replacement, the reason being is that we found the PureLine to be extremely reliable and the price is actually less than the Hayward.
 Reply


?     Asked on 4/19/2018by Vinny Pellizzi

I have a question about replacing my 1 hp hayward pump with a pureline. Since the pureline has 2" conns., if I use a 2"m X 1 1/2"f reducer bushing, will that change the alignment of the union elbow from the pump to the filter? i still want to use the EC-65 base. Thanks!
 Reply

A  Answered on 4/20/2018 by InyoPools Product Specialist Alex V.

Vinny, Using reducers should not affect the alignment of the plumbing. The Pureline Prime and Super Pump housing are similar in dimension. The only difference is the female threaded port size on the pump. 
 Reply


?     Asked on 6/12/2018by Larry

Will this Hayward Super Pump SP2607X10 work with your Hayward S244T sand filter or should I go with the 270T ? Replacing a Hayward S200 that's on it's last leg after 20 years of good service.
 Reply

A  Answered on 6/16/2018 by InyoPools Product Specialist Lennox H.

Hi, Larry. This pump can be used with either filter size as long as it does not exceed the max flow rate of the filter. Please check out Inyo's How to Size a Pool Pump for Your In-Ground Pool and How To Size a Pool Filter guides. 
 Reply


?     Asked on 6/14/2018by Gerald

18x36 inground pool. Purex Nautilus 36 DE filter which will handle 72 gallons per minute. My pool is about 27000 gals. Feet of head is difficult to estimate but I think about 50. Will a Hayward 2607 1 hp meet my needs? A pool tech told me it would. I need an answer ASAP because the pool company will replace with a 2610 1.5 hp if needed. There are no fountains or accessories and just one skimmer. I run my Polaris with a separate booster pump. Thanks
 Reply

A  Answered on 6/14/2018 by InyoPools Product Specialist Lennox H.

Hi, Gerald. With 50 feet of head using the SP2607X10 pump, your flow rate will be about 50 GPM. This pump will turn over your pool is approximately 9 hours. So it will be sufficient for your pool. The SP2610X15 will also be sufficient with approximately 65 GPM.  
 Reply


?     Asked on 7/6/2018by Ron

I have a 17000 - 18000 gallon pool with a sand filter Hayward model S-220T , 52 GPM flow . What size Hayward super pump do I need ?
 Reply

A  Answered on 7/6/2018 by InyoPools Product Specialist Lennox H.

Hi, Ron. To determine what size Super Pump you will need, calculate the Total Dynamic Head (TDH)  of your pool using Gauges or Plumbing and the info in our How to Size a Pool Pump for Your In-Ground Pool guide. 
 Reply


?     Asked on 7/6/2018by Lisa Carey

If my voltage to my Hayward superpump is 243 after the timer, is that too much for this 230 motor? Have you ever heard of this being a problem?
 Reply

A  Answered on 7/6/2018 by InyoPools Product Specialist Lennox H.

Hi, Lisa. That is not too much, the motor can operate at 10% above the rated voltage which is 253. However, it can cause the motor to run hotter/higher amps at the higher voltage and will shorten the life of the motor over time
 Reply


?     Asked on 7/7/2018by Inyo Visitor

can 1 HP super pump be replaced by 2HP model, have a 50,000 gallon pool with DE60 Hayward filter?
 Reply

A  Answered on 7/7/2018 by InyoPools Product Specialist Lennox H.

Hi. Yes, it can if your system and filter can handle the water flow. Use these following guide to determine, How To Measure Total Dynamic Head With GaugesHow Do I Calculate Feet of Head for My Pool?How to Size a Pool Pump for Your In-Ground Pool, and How To Size a Pool Filter
 Reply


?     Asked on 8/5/2018by Danny

Pool = 13,330 gallons (measured by meter when filled). A&A Mfg In-floor cleaning heads. DE 4820 filter (96 GPM max). Original Pump Hayward Super II 1.5 HP, 1.3 SF. Water Fall or Returns. 2 Main Drains, 1 Skimmer, Pool Builder says 30 feet of 2" PVC runs to Leaf Vac, then Pump, then Filter, then In-Floor cleaning system/Pool returns or In-Floor Cleaning System/Water Fall. Will 2HP 2Speed Pump work? Don't want Variable Speed
 Reply

A  Answered on 8/5/2018 by InyoPools Product Specialist Lennox H.

Hi, Danny. A 2 HP 2 Speed high pressure pump will work. I would recommend that you calculate the Total Dynamic Head (TDH) of your system using our How To Measure Total Dynamic Head With Gauges or How Do I Calculate Feet of Head for My Pool? guides. 
 Reply


?     Asked on 5/1/2019by Jamey

I'm looking for a drop in replacement for this that has variable or dual speed at 115v. Any suggestions?
 Reply

A  Answered on 5/3/2019 by InyoPools Product Specialist Joe S.

Good day, the Hayward Super Pump VS Variable Speed Pump 115V - SP26115VSP will be the drop in replacement at 115volt for the SP2607X10
 Reply


?     Asked on 5/8/2019by Joel

Looking for a new pump: Pool size is 7400 gal (kidney 13' 6" x 24' 6") Existing pump is Hayward SP3010X152S 1.5 HP port size is 2", one skimmer located at 75', sand filter is Hayward S270T max flow rate is 74GPM. What pump do you suggest if I want to keep the same plumbing? Would you recommend to go with a port size of 1 1/2 with a socket adapter to fot fit my existing piping?
 Reply

A  Answered on 5/14/2019 by Industry Professional

Are you sure the 7,400 gallons is the correct volume? On a kidney-shaped pool, we need 5 dimensions to calculate volume... widest width, narrowest width, length, shallow end depth and deep end depth could you supply us with this information? Also, will this pump be powering anything else like spa jets, solar, in-floor cleaning, water features, etc..?
 Reply


?     Asked on 5/10/2019by Norm

I THINK this is what I have. It is Hayward, 1 HP and looks like this. On motor nameplate says (bit hard to read) for model: C48K2N14381. Pump worked fine last season. Turned it on yesterday, there was a POP and GFI blew. Replace starter cap on a whim, but same thing happens every time I try turning it on. Impeller (and I assume motor) manually turns freely in pump housing. Suggestions? Is there a replacement for just the motor?
 Reply

A  Answered on 5/13/2019 by InyoPools Product Specialist Hector F.

If the motor is more than a few years old and you have replaced the capacitor then I would suggest replacing the motor. That replacement motor is model UST1102
 Reply


?     Asked on 5/20/2019by mike

my model # is c48k2n14381 what is the replacement hayward pump 1 hp
 Reply

A  Answered on 5/20/2019 by InyoPools Product Specialist Patrick P.

Hi Mike this 1 HP Hayward Super Pump on this page would be the proper replacement. You might also consider the PL2601 1 HP PureLine Prime which is a drop in replacement for the Hayward Super Pump. The only difference is the Prime has larger 2" ports.
 Reply


?     Asked on 5/21/2019by Mike

I have a 37500 gallon pool with about 50 feet of head, would a Hayward superflow 1.5 be better than the 1.0HP?
 Reply

A  Answered on 5/21/2019 by InyoPools Product Specialist Patrick P.

Hi Mike, Based on 50' of head we would suggest the 1.5 HP Hayward Super Pump or the 1.5 HP PureLine Prime
 Reply


?     Asked on 6/11/2019by Inyo Visitor

I have a Hayward super pump model c48k2n143b1 what would be a replacement pump for this? Also says sp1607z1m
 Reply

A  Answered on 6/11/2019 by InyoPools Product Specialist Patrick P.

I would suggest the 1 HP PureLine Prime as a great replacement pump for your Hayward Super Pump. The PureLine Prime is a drop-in replacement meaning the plumbing ports match up to the exact same location as your Hayward Super Pump making plumbing easy. The Prime does have larger 2" ports compared to the smaller 1.5" ports on a Super Pump if you have 1.5" plumbing then a standard 2" Male x 1.5" Slip plumbing fitting can be used. 
 Reply


?     Asked on 6/15/2019by Paul

I have a 18'x36' inground pool with Hayward pro-grid D.E. Filter model#DE2420L with a 3/4HP Hayward super pump #SP1605, can I replace the pump with a 1HP Hayward super pump model#2607 Thank you
 Reply

A  Answered on 10/15/2019 by InyoPools Product Specialist Steve M.

Paul, yes, you can use the Hayward Super Pump 1 HP Single Speed - W3SP2607X10 on your pool.
 Reply


?     Asked on 6/26/2019by S Nelsontan

How do I change the imp[eller?
 Reply

A  Answered on 6/26/2019 by InyoPools Product Specialist Kevin G.

Hello, if you click HERE, it will show you how.
 Reply


?     Asked on 7/15/2019by Werner

I have an L-shaped pool (11 x 14 outer dimension, 7 x 10 m inner dimension), depth range 0.8 - 2.0 m, 33,140 gallons, head approx. 50 ft - which Hayward pump can you recommend as a replacement for my old pump? Thank You
 Reply

A  Answered on 7/17/2019 by InyoPools Product Specialist Joe S.

Good afternoon, based on the information we would recommend Hayward TriStar 1 HP, Energy Efficient, Full Rated Pump - SP3210EE
 Reply


?     Asked on 9/3/2019by Paul

I have a hayward super pump 1hp model # C48K2N143B1. What replacement motor should I go with as I can't find that model number on line? Thanks!
 Reply

A  Answered on 9/3/2019 by InyoPools Product Specialist Joe S.

Hey Paul, we would recommend you either go with A.O. Smith 1 HP Round Flange 56J Up Rate Motor - UST1102 or our 1 HP Round Flange 56J Up Rate Motor - PL1102.
 Reply


?     Asked on 9/12/2019by Inyo Visitor

I have a 24x48x9ftdeep&3ftshallow=51840 gal-I have 1&1/2 hayward super pump-don't know my head feet-guess 50 to 70 , pipes are 1&1/2 inch what size filter do I need-sand filter-thanks
 Reply

A  Answered on 10/15/2019 by InyoPools Product Specialist Michelle B.

Hello, Here is an article on how to calculate the total feet of head. http://www.inyopools.com/Blog/how-do-i-calculate-feet-of-head-for-my-pool/Also what type of filter were you looking for? (sand,de,cartridge)
 Reply


?     Asked on 9/26/2019by Sean

I have a 33 foot round in-ground pool that is 5 feet deep. I have a center drain, skimmer, sand filter and heater that are located within 10 feet of the pool. The pipe in 2 inches, but restricts to 1 inch at the pump intake. My Hayward pump has stopped working after 10 years and all the badges have worn off in the elements so I can not tell what size pump it was. What size pump should I replace this one with?
 Reply

A  Answered on 10/11/2019 by InyoPools Product Specialist Megan C.

The PureLine Prime Pool Pump 1 HP - PL2601 would be great for the application as long as the filter rating accommodates the flow from the pump. 
 Reply


?     Asked on 4/5/2020by John

I would like to replace my Haywood Super Pump. Not sure the H.P. to replace. The old pump Haywood was a 3/4 Model C48J2N131H.P. How do I know if this was or is the correct size for my pool? It is a in ground vinyl liner pool 16' X 36" with a 6' X 3' stair extension. One simmer one bottom drain and two outlet jets.
 Reply

A  Answered on 4/7/2020 by InyoPools Product Specialist Patrick P.

Hi John, Given your pool dimensions you have roughly a 25,000 gallon pool and you will want a pump that can completely turn over 25,000 gallons in 8 hours. This would mean a pump that outputs 53 Gallons Per Minute (GPM). The 3/4 HP Super Pump will output about 48 GPM where the 1 HP will output about 62 GPM. So you are right on the border between the 3/4 HP and 1 HP and would be fine with either option. If you found that your 3/4 HP was just a little too weak then I would suggest going up to 1 HP, however, if the 3/4 HP was doing the job fine then I would stay with the 3/4 HP as it costs less to operate.
 Reply


?     Asked on 5/1/2020by Danielle Gaubert

What is the difference between SP2607x10 and W3SP2607x10? I have a 12,000 gallon, fiberglass pool with 1.5" pipes. Can you recommend a few pumps that would be a good choice for me? thanks
 Reply

A  Answered on 1/8/2021 by InyoPools Product Specialist Hector F.

Hi Danielle, there is no difference between these two pumps. The 'W3" in front of the model number merely represents the online retail part number. In order to size a pool pump, there are a number of variables to consider. Here is a guide that we put together called "How to Size a Pool Pump for Your In-Ground Pool" that may assist with that. 
 Reply


?     Asked on 5/12/2020by Lawrence

Have a Hayward 2420 DE filter with 1 1/2 inch lines. Flow rates nearly the same. Lines are within 10 feel from the pool. Would this be an optimal pump?
 Reply

A  Answered on 12/7/2020 by InyoPools Product Specialist Hector F.

Hi Lawrence, there a few variables to consider when sizing a pool pump. Here is a guide that we put together called "How to Size a Pool Pump for Your In-Ground Pool" that should assist with that. 
 Reply


?     Asked on 6/2/2020by Alice

what is the difference between Hayward pool pump W3SP2607x10 and SP2607x10?
 Reply

A  Answered on 6/2/2020 by InyoPools Product Specialist Patrick P.

Hi Alice, As far as the pump goes there is absolutely no difference between the W3SP2607x10 and SP2607x10. The only difference is the warranty the W3 prefix indicates that if the pump was purchased online through the internet then the pump comes with a manufacturer's warranty. If you purchase the version without the W3 through the internet then the manufacturer does not supply a warranty.
 Reply


?     Asked on 6/29/2020by Red

My pump finally went out. My pool is rectangle, close to 40,000 gallons. What would be the proper hp for my new pump?

 Reply

A  Answered on 10/22/2020 by InyoPools Product Specialist Hector F.

Hi Red, here is a guide that we put together called "How to Size a Pool Pump for Your In-Ground Pool" that should assist. 
 Reply


?     Asked on 8/11/2020by Nick

Good Morning, I have a 40X16 Lazy L pool that is 3 feet deep in the shallow end and 9 feet in the deep end. I think our filter is starting to fail and we are looking to replace. What is the correct size that I should be looking for?
 Reply

A  Answered on 8/11/2020 by InyoPools Product Specialist Lennox H.

Hi, Nick. You can use the info outlined in our How To Size a Pool Filter and How to Size a Pool Pump guides to determine the correct size for your pool. 
 Reply


?     Asked on 9/29/2020by eugene lenhardt

what is the rpm speed of the Hayward W3SP2607X10 Super Inground Pool Pump, 115/230V, 1 HP?
 Reply

A  Answered on 10/28/2020 by InyoPools Product Specialist Joe S.

Good afternoon Eugene, the W3SP2607X10 runs at 3450 RPMS.
 Reply


?     Asked on 5/9/2021by Mark

I have a Hayward super pumped dual speed model # c48k2n141. What do you recommend replacing the pump and motor with
 Reply

A  Answered on 5/10/2021 by InyoPools Product Specialist Patrick P.

Hi Mark, If you don't want to do any re-plumbing then I would suggest the Hayward Super Pump Variable Speed Pump if you don't mind doing a little re-plumbing then I would suggest Waterway 1.65 HP Variable Speed Pump as it is a similar quality pump but at much better price point.
 Reply


?     Asked on 5/10/2021by JOHN CAPPELLO

WHERE CAN I GET MOTOR REBUILT?
 Reply

A  Answered on 5/11/2021 by InyoPools Product Specialist Patrick P.

Hi John, We do not sell re-built motors or aware of place to purchase those. If you are needing the replacement motor for this 1 HP Super Pump, then the proper replacement motor will be this UST1102 1 HP Replacement Motor. Could you send us a few photos of your pump and motor to ensure you are purchasing the correct replacement? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
 Reply


?     Asked on 8/22/2022by William R. Boyd

I have the Hayward super pump Model # C48K2N143B1 is the Hayward W35P2607X10 The direct replacement for this model now (Motor, basket, housing etc.)?
 Reply

A  Answered on 11/30/2022 by InyoPools Product Specialist Hector F.

Hello William, yes the complete Hayward Super Pump model W35P2607X10 replaces the Hayward Super Pump that uses the motor model C48K2N143B1. 
 Reply


?     Asked on 8/30/2022by Bonnie Artz

Is this pump self priming
 Reply

A  Answered on 9/1/2022 by InyoPools Product Specialist Craig C.

Hello Bonnie.  The Hayward Super Pump 1 HP Single Speed - W3SP2607X10 is a self-priming pump.  
 Reply


?     Asked on 9/24/2022by Rhonda Adams

does this pump come with 1.5 ports my plumbing is all 1.5 inch
 Reply

A  Answered on 10/3/2022 by InyoPools Product Specialist Hector F.

Hi Rhonda, this pump comes with 2 inch ports however you can use reducer union fittings such as part number 21063-154-000 to modify that as well. 
 Reply


?     Asked on 10/12/2022by Inyo Visitor

What is the gpm
 Reply

A  Answered on 10/12/2022 by InyoPools Product Specialist Craig C.

Hello.  Attached please find Product Detail information for the Hayward 1.0 HP Super Pump W3SP2607X10.  Hayward Super Pump 1 HP Single Speed - W3SP2607X10  Please reference the Performance Data graph.  The Super Pump W3SP2607X10 is rated at 50 GPM @ 50 Ft of Head.
 Reply


?     Asked on 8/4/2023by Elizabeth Rogers

I want to replace an old 1hp pump with 1.5 inch pipe to superpump which has 2 inch openings. What do I need to convert it
 Reply

A  Answered on 8/4/2023 by InyoPools Product Specialist Rich N.

Hi Elizabeth, just get two of these CMP 2" MPT, 2" Socket Union, Single - 21063-200-000 and two of these Reducing Bushing 2 x 1-1/2" Slip x Slip (437-251) and you will be all set!
 Reply


?     Asked on 9/22/2024by Lisa

Does this pump come with a power cord ?
 Reply

A  Answered on 9/23/2024 by InyoPools Product Specialist Rich N.

Hi Lisa, this inground pool pump does not come with a power cord.  It is meant to be installed with watertight conduit per National Electrical Code.  
 Reply