?     Asked on 5/6/2018by Michael Ferro

I would like to upgrade Hayward Super II 1.5 HP pump motor #K48M2N110 with 2.0 HP pump motor, what motor # & seal kit #? The pump #SP3015EEAZ, would I also have to replace the impeller and if so what part #?
 Reply

A  Answered on 5/6/2018 by InyoPools Product Specialist Lennox H.

Hi, Michael. The pump you have is already a 2 hp model. You have a 1.5HP Full Rate model which has a total HP of 2.25. The next size up will be a 2.7HP. You will need the B231SE - Motor, Impeller / Diffusser / Upgrade Kit - SPX3020CKIT, Impeller Ring - SPX3021R, and Tune Up Kit - GOKIT2 or GOKIT2SALT. Only make this upgrade once you've confirmed that your system can handle the additional water flow. 
 Reply


?     Asked on 5/9/2018by lcv

hi will this motor fit 12 year old super pump 2 with a 2hp motor? thank you.
 Reply

A  Answered on 5/9/2018 by InyoPools Product Specialist Hector F.

We would need to know the specific motor model, part or catalog number to confirm. If you cannot locate that information then you can email images of the pump to upload@inyopools.com and locate the impeller part number so we can assist further. 
 Reply


?     Asked on 6/9/2018by nathan

Need replacement Hayward NorthStar 2 hp 208-230 SP1620-z-1-bns
 Reply

A  Answered on 6/9/2018 by InyoPools Product Specialist Alex V.

Nathan, based on your motor model number, you will need the SN1202 motor. Be sure to replace the shaft seal when you replace the motor. 
 Reply


?     Asked on 7/17/2018by Greg

When mounting the motor should the capacitor be on the top or the bottom?
 Reply

A  Answered on 7/18/2018 by InyoPools Product Specialist Hector F.

The capacitor that you see on this motor is to be facing up. 
 Reply


?     Asked on 9/7/2018by Remy

Will this motor work with a 120 volt intermatic timer? Is this considered a 120 volt pool pump?
 Reply

A  Answered on 9/7/2018 by InyoPools Product Specialist Lennox H.

Hi, Remy.  Yes, this motor will operate using 120 volts. 
 Reply


?     Asked on 10/6/2018by June E Byers

Hello, I need to replace a 2 HP Century pool pump motor Model K48N2Nn106C1. Do you know if this will be a match? Original pool pump is 15 year old Haywood. Not sure the model though.
 Reply

A  Answered on 10/10/2018 by InyoPools Product Specialist Hector F.

It seems as if you have an extra letter "N' in the model number and if so the actual two single speed options that you can use are the ST1202 or the UST1252
 Reply


?     Asked on 11/14/2018by Lodewyk Steyn

Hi, Is this a suitable replacement motor for SP3015X20AZ. I currently have an Emerson T55CXJN-1348 2hp motor on there which locked up. What else would be needed for repair overhaul while I'm in there. The pump operates a saltwarter pool/spa. Regards
 Reply

A  Answered on 11/14/2018 by InyoPools Product Specialist Hector F.

Yes, this motor will work as a replacement motor for the model SP3015X20AZ pool pump. 
 Reply


?     Asked on 1/17/2019by richard shafii

Is the shaft 3/4"?
 Reply

A  Answered on 1/18/2019 by InyoPools Product Specialist Lennox H.

Hi, Richard. The shaft diameter is .625". 
 Reply


?     Asked on 2/14/2019by james green

I have a Hayward max flo super II pump. I need a replacement motor. The only number I can read on the pump is SP1615-Z-1--MXBK. I can't find a replacement. Please help.
 Reply

A  Answered on 2/14/2019 by InyoPools Product Specialist Michelle B.

Hello, Can you please send a picture of the motor label?
 Reply


?     Asked on 3/15/2019by Joe

Will this motor replace my SP-1615-Z-1-M motor?

 Reply

A  Answered on 3/15/2019 by InyoPools Product Specialist Michelle B.

Hello, Can you please provide a side view of the entire pump?
 Reply


?     Asked on 3/29/2019by FRED THOMPSON

Motor just humming is this wiring correct 230

 Reply

A  Answered on 3/29/2019 by InyoPools Product Specialist Lennox H.

Hi, Fred. The motor does appear to be wired correctly. Please test the voltage to make sure that you're getting 230 volts.
 Reply


?     Asked on 3/29/2019by FRED THOMPSON

Motor just humming is this wiring correct 230

 Reply

A  Answered on 3/29/2019 by InyoPools Product Specialist Lennox H.

Hi, Fred. The motor does appear to be wired correctly. Please test the voltage to make sure that you're getting 230 volts.
 Reply


?     Asked on 4/17/2019by Rita

Will your pump be the right replacement for the one in the attached photo?
 Reply

A  Answered on 4/18/2019 by InyoPools Product Specialist Lennox H.

Hi. Yes, this PL2230 can be used as an alternate replacement. You will also need the Hayward Super II Pump Tune Up Kit - GOKIT2 or GOKIT2SALT.
 Reply


?     Asked on 4/17/2019by Inyo Visitor

Is your part the right replacement for the attached photo?

 Reply

A  Answered on 4/18/2019 by InyoPools Product Specialist Lennox H.

Hi. Yes, this PL2230 can be used as an alternate replacement. You will also need the Hayward Super II Pump Tune Up Kit - GOKIT2 or GOKIT2SALT
 Reply


?     Asked on 6/19/2019by Ronald White

Is this motor a replacement for my motor - it is US Motors 1081 Pool Motor, Cat No. EB809, Model K63CXERA-4768, HP 2.0, SF 1.20 RPM 3450, Volts 208-230, HZ 60, SF Amps 10.3-9.5, PH 1 Duty Cont, MFG L11C Frame 56J INS Class B. Thermally Protected AUTO Code G AMB c 50, Code 00D10 Made in Mexico EB809 , will replace myself if this one will work on my pool.

 Reply

A  Answered on 6/19/2019 by InyoPools Product Specialist Hector F.

Unfortunately, this motor will have a lower service factor so it would not be a match. You would want to go with the 5224A.
 Reply


?     Asked on 6/22/2019by Eric

We ordered this pump motor from Inyo. I have the motor installed but, it didn't come with wiring instructions for 230V. I have a black, red, gree (ground). No where on the motor is the typical 115/230v switch or instructions for wiring 115/230 Help!

 Reply

A  Answered on 6/23/2019 by Pureline

Eric, For 230v, the white and orange wires should be connected to the A terminal. Since you have 230v, your black and red wires are 115v hot. So either the black or red need to go to Line 1 and the other to Line 2. Your ground would be attached to the green ground screw.
 Reply


?     Asked on 6/24/2019by Philip Saluter

is this high or low head
 Reply

A  Answered on 6/24/2019 by InyoPools Product Specialist Matt S.

This is just a motor, it does not have a head rating. Only whole pool pumps would be rated for a certain category of total dynamic head.
 Reply


?     Asked on 7/4/2019by Amy

I need to replace a Century K48M2PA105C5 motor 2HP, 230V, 3450rpm, 10.4amps that is on my Hayward pool pump for the waterfall feature. Is this a suitable replacement?
 Reply

A  Answered on 7/10/2019 by InyoPools Product Specialist Matt S.

Yes, the PL2230 is a suitable replacement for the USQ1202
 Reply


?     Asked on 7/8/2019by Douglas Shelton

Will this motor replace my Hayward Super pump 2.0 HP? Current motor is a Century Model K48M2N111 Serial# 31913J2

 Reply

A  Answered on 7/8/2019 by InyoPools Product Specialist Joe S.

Good afternoon, yes if you have the K48M2N111 the 2 HP Round Flange 56J Up Rate Motor - PL2230 would be a replacement for it.
 Reply


?     Asked on 7/31/2019by Mario

What are capacitor specs for this pump?
 Reply

A  Answered on 9/27/2019 by InyoPools Product Specialist Michelle B.

Hello, We recommend contacting the manufacturer with that question. You can reach them at 1-877-372-6038.
 Reply


?     Asked on 8/14/2019by Richard Smith g

I bought this pump about a year ago. I have replaced the factory capacitor and another replacement one. Does being in Texas with hot weather play apart in these going out? Is there a heavier duty replacemnet for it. If not what is the exact replacement? Shortly after buying our house I had to buy a new motor. Maybe it getting different voltage than it need.
 Reply

A  Answered on 8/14/2019 by InyoPools Product Specialist Lennox H.

Hi, Richard. The ambient air temperature will affect the motor. I recommend using a Protective Pool Motor Cover - R221016.
 Reply


?     Asked on 9/9/2019by Ryan

Replacing a motor on Hayward model #SP3015EEAZ, is this the correct motor to replace it with? The current motor is UST1202 model K48M2N110C2. Thank you
 Reply

A  Answered on 9/10/2019 by InyoPools Product Specialist Joe S.

Based on the information provided you will need to order A.O. Smith 1.5 HP Round Flange 56J Up Rate EE Motor - UCT1152
 Reply


?     Asked on 3/27/2020by Tom

I presently have a Century Centurion motor with a Jandy PHPU 2.0 pump. The part is "8-193633-24" , 56J. What is the correct replacement energy efficient motor?? Thanx.
 Reply

A  Answered on 3/27/2020 by InyoPools Product Specialist Patrick P.

Hi Tom, Yes as long as you are wiring your motor 230V then this PL2230 would be the correct motor. The 193633 had an option to 115v or 230v where the PL2230 can only be wired 230v. When replacing your motor you will also need this Jandy Stealth Shaft Seal. If you want to go with an extremely energy efficient motor than we would suggest this 2.7 HP Variable Speed Replacement Motor
 Reply


?     Asked on 7/4/2024by Jeff

I have an Emerson motor model K63CXERA-4768 The compositor is at the rear of the motor, will this one be a good replacement? Mine just froze and i cant get it to turn.
 Reply

A  Answered on 7/5/2024 by InyoPools Product Specialist Robert M.

The PL2230 would not be the correct replacement motor. The correct replacement motor for California is part number NPTT270.  
 Reply