Part # UST1152
Warranty 1 Year
Dimensions 14" L x 5.5" W x 5.5" D
Century UST1152 Details
Voltage 115/230, Max Amps 115V = 18.6 230V = 9.3, Single Speed, Round Flange, RPM = 3450, Threaded Shaft, Frame = 56J Used on the following models: Hayward Max Flow, Hayward Super Pump, Hayward Super II, Hayward Northstar and Jacuzzi Magnum pumps.
Don't Forget Your Tune Up Kit
Hayward Super Pump Tune Up Kit
Hayward Super II Tune Up Kit
Hayward Max-Flo Tune Up Kit
Jacuzzi Magnum Tune Up Kit
Note: NOT California or New York Title 20 Compliant.
California and New York Title 20 Compliant Options:
I have a Hayward Supper II single speed 1 1/2 HP pump. What do I need to consider to replace the single speed motor with a dual speed motor?
Reply
Check the SF on the old and new motor. The product of the SF and HP has to match. If your old motor has a SF of 1.0, its actual HP is 1.5 (1.5 HP x 1.0 SF). If that's true you should replace it with 1 HP dual speed motor (STS1102). With a SF of 1.5, its actual HP is 1.5 (1.0 HP x 1.5 SF). Also be aware that you will have to buy a hi/lo switch. It is not provided with the motor.
Reply
My pool pump motor makes a humming noise when I try to start it. Will replacing the motor fix my problem?
Reply
Will the AO Smith UCT1152 cost less to run than the UST1152?
Reply
Yes, the UCT1152 will cost less to operate compared to the standard UST1152. Depending on how the motor is cared for, it should last several years. When replacing the motor, I would recommend buying a tune up kit based on your pump model and age.
Reply
Trying to replace Emmerson pool pump motor EUST1152, what motor should I purchase to replace this 1.5 hp motor?
Reply
I would sugget this Ao Smith / Century brand motor here which is a direct replacement for the Emerson EUST1152 motor.
Reply
1 to 2 hrs
Screwdriver, Socket Set
I shopped around and found the motor at INYO at a good price. Mostly the reason I went with INYO was the info I received from the chat person. Very helpful info and very prompt. They also told me which rebuild pump seal kit to purchase, based on the Hayward pump model number I supplied to them. This is a company I would have no hesitation to recommend.
Less than 1 hr
Screwdriver, Socket Set
4 0
I order a replacement Century motor and the experts at Inyo provided the correct replacement and parts needed. Simply unscrew the motor from the pump making a photo of where everything goes. The diagram from Inyo is clear as tap water so its easy to remove and replace the various components. Once done, re-attach it to the pump and away you go. No experience required for this repair
Less than 1 hr
Screwdriver, Nut Drivers, Socket Set, Wrench Set
4 0
I turned off the power to the pump,and disconnected the wiring to the motor.
Next the pump wet end was drained.
The 6 motor mounting bolts were removed.
The motor was removed and diffuser and impeller removed.Then the seal assembly was replaced,and the above steps were reversed for reinstallation.
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set, Adjustable Wrench
4 0
Took the old motor off, which is the only 4 bolts that can be seen. And also unwired the pump. I took the motor inside because it was close to 100 degrees outside. There is still plastic parts that have to be removed from the motor and revolted to the filter box. Used a 7/16 wrench to hold the shaft while spinning the shaft off. Once that was off could remove the other bolts and then take the rest of the plastic part off. Attached it to the new pump. Bolted the plastic to the the new motor and then spun the shaft back on ( this does not need to be tightened as using the pump will tighten it). Then took the motor back outside and bolted it back to the filter box part of the pump assembly. Only thing I didn't do was change the gaskets. I did order new ones and will replace when I get them.
Less than 1 hr
Screwdriver, Nut Drivers, Pliers, Electrical tools
5 0
The motor that I had stopped working after 25 years. After doing some research I decided on this motor. The whole process took me less than 1 hour. I had to wire the cable for the electric. I’m very familiar with doing this so it was easy to do. It hooked up to the pool plumbing since it was identical to my old pump. Here’s to another 25 years of zero issues.
Less than 1 hr
Screwdriver, Socket Set, Wrench Set
4 0
This was a replacement motor for the Hayward motor that was there when we bought the house in 2011. That pump ran forever!
The install was not difficult, but did take some time to be sure we did it correctly. I HIGHLY recommend taking the time to watch the video & read the installation guide. Compare them & ask questions via chat even before you begin. Don’t rush & the install will be great!
I will say, however, that right as we were approaching the 2 year mark the impeller snapped & of course the motor stopped working. Now I am ordering a replacement that will HOPEFULLY last longer than the original.
1 to 2 hrs
Screwdriver, Nut Drivers, Socket Set
6 0
2 to 4 hrs
Screwdriver, Nut Drivers, Socket Set, Wrench Set
4 0
Removed old motor from pump by 4 bolts. Detached power supply wires from motor, and ground wire from housing. Obtained video information from INYOPools.com site. Following video instruction, disassembled all pump-related components from front of motor, including removing motor end cap to access motor spindle. Ordered new gasket kit and reinstalled pump-related components to new motor. Reattached electric wiring and reinstalled motor into pump housing unit. Motor runs well, but has small drip coming from pump impeller location, so I will need to investigate further. Outstanding and timely service by INYOPool to promptly deliver new motor.
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set
4 0
Hardest part was to bypass the water connections to remove the filter from the pool. Four bolts remove the motor and part of the filter, four more separate the filter halves. and permit access to the seal parts. Replacing the seal is a matter or pulling it off and replacing it with the new seal (assuming I had the KIT 1 I had ordered and failed to arrive with the motor) Reversed all the action and removed the motor cover. Replaced the cord making sure to set the voltage selection if using the 115 voltage.
2 to 4 hrs
Screwdriver, Pliers, Socket Set, Wrench Set
8 0
Received motor
Disassembled old motor from pool pump
Long socket wrench needed to remove 4 mounting bolts from pool pump
Remove AC wire
Remove impeller from old motor
Replace existing impeller on to New motor
Reassemble motor to pool pump
Connect AC to motor
Engage circuit
Prime pool pump
Works great
1 to 2 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Adjustable Wrench
4 0
I followed this video on INYO Pools - https://www.youtube.com/watch?v=mpJLp3oWDGU&feature=youtu.be
Yes I watched it several times but made it very simple. Biggest problem was removing the existing impeller. Had to take the broken pump completely apart.
Save yourself the time and buy new impeller and restrictor cover.
1 to 2 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set
3 0
2 to 4 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set
2 0
Removed and disassembled motor/impeller assembly per the Inyo Pools instructional video (well done!), with the following notes:
I could not get the impeller off by hand, and had to resort to GENTLY using a small screwdriver, inserted into one of the vane openings on the outer edge of the impeller, in order to get leverage - it worked like a charm! I used an appropriately sized socket to remove the ceramic shaft seal by gently pounding it from the opposite side of the ceramic part. Other than that, the operation went as planned!
Less than 1 hr
Screwdriver, Socket Set
2 0
First I looked on line for Companies that had our model motor and their cost! The INYO Pools were the company with best price and model for replacement! The web site was easy to use and time of delivery time as very short! I had just had back surgery so my son came over and replaced the new motor! With the model being the same the process to replace went very fast and instruction from your company very easy to follow! Would recommend this company to friends and for future use.!
Less than 1 hr
Screwdriver, Socket Set, Wrench Set
2 0
Watched the inyopools YouTube video on how to replace the motor. The video made it really easy. Took about 30 minutes from start to finish. New motor runs smooth and is a lot quieter than the old motor.
2 to 4 hrs
Screwdriver, Nut Drivers, Adjustable Wrench
2 0
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set
2 0
First I tried to replace Solenoid on the old motor but when power was put to it it just smoked out ( burned ). Then went onto Lesile pool website to match Hayward motor but seeing their crazy price I searched the web and came upon INPOpools.com site and they had an AOsmith motor that would replace my Hayward exactly.
Ordered it and showed my pool store guy and he said this is a great motor and so I took the impeller apart and replaced the AOsmith motor so easily. I can't believe how much more quieter it is than the Hayward and strong 1.5 HP.
Thanks INPOpools my new pool store!
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set
4 1
1) Disconnected the electric.
2) Removed the old motor from the housing.
3) Installed new seal assembly.
4) Installed impeller.
5) Installed diffuser.
6) Replace the diffuser gasket.
7) Bolted new motor to pump housing.
8) Reconnected electrical wiring.
1 to 2 hrs
Wrench Set
2 0
Upon discovery the pump was inoperable. Simple discovery motor went out. I searched and found the right pump/price. Ordered from Inyo pools and received part promptly. Removed the old motor and reinstalled the new motor. Waalaa. Pump in operation and pool open once again. Thanks Inyo Pools supply.
1 to 2 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set
3 0
First trip the circuit breaker, drain the water from the pump system, remove the bolts that connect the motor to the pool water pump, remove the cover at the other end of the motor.
Disconnect the three (3) electric wires from the motor, short the capacitor to ground remove the capacitor with a 1/4" nut driver, use a 7/16" open wrench to hold the motor shaft from turning.
On the other end of the motor turn the diffuser c.c. wise to remove it from the shaft, put new seals on the shaft of the new motor. Use the same diffuser that you removed from the old motor, connect the electric, put the dust cover back on and re-bolt the motor to the pump, reset the circuit breaker. your good to go.
Less than 1 hr
Screwdriver, Socket Set, Wrench Set
2 1
I order the replacement from Inyopools.
1.made sure power was off to motor
2.removed the 2 screws holding the end cap. You don't have to unscrew it all out.
3. Disconnected the 2 power leads and ground wire. Note where you removed them from.
4. Removed 4 bolts attached to pump, and slide out.
5. Remove infuser. Pull right out. Notice the label Top on the cover.
6. Remove from bolts from housing.
7. After parts are removed, clean them and check for reuse.
8. Reinstall housing in reverse order on new motor.
9. After all of the connections are made, make sure to add water to prime pump and start. Check for any leaks.
Follow the removal video from inyopool.
1 to 2 hrs
Pliers, Socket Set, Wire strippers
3 0
Less than 1 hr
Screwdriver, Pliers, Socket Set
2 0
Super simple install. Unbolted old motor, broke down seal plate as well as impeller, replaced shaft seal into seal plate and impeller then when back through the steps in reverse for the reinstall!!! Awesome replacement motor. Anybody could do it.
2 to 4 hrs
Screwdriver, Socket Set, Wrench Set
2 0
Pool motor quit working, ordered new motor, installed and still not working. Checking more found timer box had quit working. Not sure if old motor is good but saving it just in case. Pool motor working good now!!!
Took longer to do the job because of the additional troubleshooting, also made sure it is sealing right to make it prime right!! Challenging to do but once you become familiar with it, it’s easy to understand!!
Less than 1 hr
Screwdriver, Nut Drivers, Pliers, Socket Set
2 0
1 to 2 hrs
Wrench Set
4 0
1 to 2 hrs
Screwdriver, Pliers, Socket Set
3 0
I removed the old motor from the pump housing. I then removed the power cord from the old motor. I removed the cover to the new motor. I verified the new motor was set to the proper voltage which was 230V for my setup. I carefully discharges the capacitor to insure no nasty shock. I then carefully connected the old power cord to the motor and put on the cap. I bolted the new motor to the pump housing and plugged in the pump.
1 to 2 hrs
Screwdriver, Socket Set
2 0
1 to 2 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Adjustable Wrench
4 0
Best part is the pool motor arrived 2 days earlier than I was expecting. I had some questions about the accesory kit. for the installation..The support was great. I had to upload the picture of my pool motor which he reviewed and suggested the right kit.
The installation was easy once you watch the step by step DIY video provided by inyo pools.
Need to follow the video carefully to avoid leaks. Overall great experience.
Great price.Great support. Recommend highly
1 to 2 hrs
Screwdriver, Nut Drivers, Socket Set
2 0
1 to 2 hrs
Screwdriver, Nut Drivers, Wrench Set
3 0
Easy direct replacement to the Hayward Super pump. Local pool shop wanted almost 2x the cost of the motor as INYO pools. Online instructions were great, and the follow up emails on how to install the motor made this really easy.
I have replaced the motor before, but it has been over 5 years, so the refresher course/tutorial that was available was very much appreciated.
At first, I did not know how to take the company name, and decided to give them a shot. I am glad I did. I have since purchased additional parts and accessories from this company.
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set
2 0
I removed the old motor, switched the impeller over to the new motor, replaced the seals, and reinstalled the new motor. The project was very easy, with the most important part being to shut off the power to the pool before disassembly.
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set
4 0
I'm still a novice at pool maintenance.
This is my 3rd summer ever owning a home with a pool.
Opened ourselves with the help of a friend who works in the field.
I have 3 pumps, Main, Spa booster and Waterfall.
The main pump was replaced last year along with a new DE filter and a couple of actuators at a cost of $2000+ by a local company a week before a big party we had planned with 50 guests coming.
After that experience I was done being robbed
This year the Spa pump was right at the end of life (loud as hell) and waterfall pump tripped breaker or would just stop after 30 minutes of run time.
There was no way I was going to go back to the local company.
My friend would have charged me a nominal fee for his time but I figured I would give it a try on my own watching the video and following advice online.
The first pump was a learning curve but the second was a breeze.
The online help and customer service at InYoPools were super helpful.
I recommend also getting a Seal Assembly kit and replace with all new when replacing the motor.
Also which is not noted in the video or article to get a SLINGER FOR the MOTOR SHAFT.
I missed that and had to reopen the first motor and did not find out until I was halfway through the install of the second motor when checking other sites online.
AND be safe everyone. turn off your power to the system before opening anything.
1 to 2 hrs
Screwdriver, Socket Set, Adjustable Wrench
5 0
I was fortunate by contacting Inyo and talking to Adam. He convinced me I could handle the replacement process and save some money. He spent time gathering the necessary information to get me the correct motor. He walked me thru the entire process and forwarded a video . I made a call back as I was unsure of the wiring . Once again Adam went over the correct setup. I am happy to report success. Because of people like Adam I will always call Inyo Pool. Your people are your most important Product!!!!!!!!
Less than 1 hr
Screwdriver, Socket Set, Wrench Set
11 0
My Haywood pool pump had quite running. When I turned it on it would only hum. Through research I determined that it was needing replaced. I found Inyopool during my online searches. Their prices were the best I found. The replacement was easy. I did order the tuneup kit, as recommended on their site. It took less than 30 minutes to install the tuneup items, and the pump. I referred to the online videos that were provided to me by Inyopool.
For the project you will need a screwdriver, a wrench (to hold the shaft in place while you tighten the impeller), and a socket set.
1. Remove your old pump, and take off the plastic housing that goes from the pump to the filter basket.
2. Clean up the pieces you will be reusing (all the plastic pieces)
3. Replace your shaft seal parts, be sure to lube the areas shown in the video
4. Now you can attach all the plastic parts onto your new pump.
5. Tighten the 4 bolts being sure to tighten each snug, before tightening all.
6. Attach your power wires, and your ground wires, put the back cover on and turn your breakers back on.
7. Final step is to refill the filter basket with water, once it is full, your new pump will be ready to roll.
Biggest recommendation is to watch the Inyopool videos. I am a female, and I was able to complete this without any problem, thanks to their step by step videos.
2 to 4 hrs
Screwdriver, Pliers, Socket Set, Adjustable Wrench
6 0
The motor was removed from the pump housing and inspected. It had locked up due to moisture from a leaking housing. A new motor and seal kit was ordered for replacement, delivery was made in 2-3 days and the repair was completed using instructional videos on the INYO website. This was my first attempt at a pump repair and everything went smoothly. Thanks to INYO for the quick delivery of parts and detailed instructions on the repair!
The Most Recent Reviews
(5 out of 5 stars) Hayward pool pump motor
Reviewed By: Joseph L. from San Antonio, TX ()
Pros: price
Cons: none
Great price and a perfect fit.
Was this review helpful to you?
(5 out of 5 stars) Replacement Motor
Reviewed By: Joseph B. from Long Island, NY ()
Perfect replacement part for our Hayward pool filter.
Was this review helpful to you?
(5 out of 5 stars) Replacement motor
Reviewed By: Debra R. from Winchester, NH ()
Perfect replacement motor for my Hayward pump. Can't beat the price, or the super fast shipping from Inyo Pools! Thank You! : )
Was this review helpful to you?
(5 out of 5 stars) Great motor
Reviewed By: John R. from Boone Iowa ()
I’m really impressed with the motor and how well it fit my pump, very glad I brought it.
Was this review helpful to you?
(5 out of 5 stars) Great replacement motor
Reviewed By: Chris D. from Jacksonville, FL ()
Pros: Quiet, easy to install, cost effective
Cons: None
This motor is a great replacement motor for they Hayward Super Pump. Runs just like the OEM. Saves a bunch of money for the DIY'er. Runs quiet and fits all existing parts on the Hayward housing. Easy to replace in about an hour.
Was this review helpful to you?
(3 out of 5 stars) Works decently, not as quiet as I hoped
Reviewed By: Michael W. from Arlington TX ()
Pros: relatively easy to install
Cons: still runs hot, not as quiet as I had hoped
The installation instructions were practically non existent and it would have been nice to have some type of confirmation that I was hooking up correctly. Runs very hot, so had electrician come to make sure I had properly wired. Still runs hot, but never shuts off so I thinks it's just the nature of the thing. I wish it was quieter
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Terry B. from Mantachie, MS ()
Product was as advertised. Works just like the one I took off before it broke
Was this review helpful to you?
(5 out of 5 stars) Quiet, efficient motor
Reviewed By: Carla S. from Yutan, NE ()
Pros: quiet
Cons: none
I needed to replace the 4 year old pump in our swimming pool. My wife convinced me to just replace the motor since you have numerous "how to guides" on your website explaining how to do it and doing so would save $200. It only took a few hours (2-3) and wasn't a bad job my any means. The new pump is noticeably quieter than the old and works just fine!
Was this review helpful to you?
(5 out of 5 stars) Replacement Filter Motor
Reviewed By: Nancy S from Freehold, NJ ()
Pros: Everything...product; customer service, delivery A++
Cons: N O T H I N G !!!!
WOW.....this company and the products they sell are AMAZING! The product was just what was ordered. I even called their 800 number for some helpful information before ordering and they were so knowledgeable. I placed the order at about 10am on Wednesday and it was at my door Friday afternoon. WOW!!! (sorry, but it bears repeating!)
Was this review helpful to you?
1 0
(5 out of 5 stars) Pump Motor
Reviewed By: David S. ()
Pros: Exact motor match, helpful instructions
Pump fits & runs perfectly. The directions from inyopools.com for installation was easy to follow and very helpful.
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Lem K. from California ()
Pros: Fast Service, Polite Customer Service, Good Price
Cons: None
Great service, I called my order in so I would get the right seal kit. Fantastic customer service/support and fast shipping. I had a professional do the install it was worth it even though I could have done it myself. This is my first order to INYO and I'm finding parts for my slide that I need. Look forward to doing business again. Thank you
Was this review helpful to you?
1 1
(1 out of 5 stars) Replacement needed after 7 months
Reviewed By: Michael C. from charlotte, nc ()
Cons: Didn't last
I had to get a replacement for this motor after only 7 months!
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Thomas W. from Goose Creek, SC ()
Pros: excellent product- they tend to last longer than others
Cons: The cost when you have to replace them. LOL
The motors are very reliable and easy to change out.
Was this review helpful to you?
2 0
(5 out of 5 stars) Easy Install
Reviewed By: Mark R. from Alexandria, VA ()
Pros: Installation, noise level
Cons: none yet!
This pump was very easy to install, and runs very quietly. Two possible improvements - Markings on the power terminal could be more clear for the 110 and 220 settings, and it would be helpful if a sticker with punch outs for month/day/year was included, so the install date could be recorded on the outside of the unit. We are quite pleased with the unit, and the neighbors are enjoying the quiet.
Was this review helpful to you?
3 0
(5 out of 5 stars) Easy install
Reviewed By: Valerie R. from Grand Prairie, TX ()
Pros: Quieter than older model. Easy to follow instructions.
Cons: None
I bought this motor as a replacement for an older model that finally gave out. I followed the written instructions I found on INYOs site (and watched the installation video). I was able to get my pool up and running in under 2 hours with no problems (I was being VERY careful since I have no experience in this area). I used my cell phone to take pictures of the wiring before I disconnected just to ensure I reconnected everything correctly. Motor is actually quieter than my previous one. Thanks INYO for providing everything I needed to complete this project myself!
Was this review helpful to you?
1 0
(5 out of 5 stars) Powerful and quiet; awesome pool pump motor!
Reviewed By: William M. from Judsonia, AR ()
Pros: Quiet and powerful
Cons: None
Replaced a loud underpowered pool pump motor with the A.O Smith 1.5 HP motor. You now have to go around the corner to hear the pump and boy does it push the water. Family outings are a lot more fun now that we can hear each other speaking normally instead of yelling.
Was this review helpful to you?
1 0
(5 out of 5 stars) Great Service
Reviewed By: Timothy H. from Catawba, SC ()
INYO Pools was very prompt in shipping my product and getting it to me in a timely manner. My pool was down and the temperatures were starting to rise and I was worried that I was going to have problems before getting the pools started again. But I received the new pump motor in just a couple of days and the fit was perfect. Thanks INYO
Was this review helpful to you?
1 0
(5 out of 5 stars) Pool Pump at Perfect Price
Reviewed By: Joshua M. from Manalapan, NJ ()
I needed to replace my pool pump motor. After looking online INYO Pools carried the same motor for the best price out there. The product shipped by Ground Service via UPS and it still arrived faster that I thought it would.
Was this review helpful to you?
(5 out of 5 stars) Easy Install
Reviewed By: Ed D. from Clermont, FL ()
Worked as described.
Was this review helpful to you?
1 0
(5 out of 5 stars) inyo pools is the way to go
Reviewed By: R H. from hollywood, FL ()
Pros: do your self and save $$$$$
Cons: need more instructions with unit
replacement of the motor is easy __great product great help thanks Ray
Was this review helpful to you?
1 0
(5 out of 5 stars) Quality Motor
Reviewed By: David M. from Kathleen, GA ()
Pros: Price and Quality of the product
Cons: None
Received pool pump motor in excellent condition. Very easy to install with the direction provided. Don't forget to get a new seal kit to install on motor
Was this review helpful to you?
2 0
(5 out of 5 stars) replacement pump motor
Reviewed By: Keith M. from clermont, FL ()
Cons: none
exact replacement motor new best price i found in my search easy to nav the site shipped within 24 hrs. pool up and running 5 days after ordering.!!!
Was this review helpful to you?
1 0
(4 out of 5 stars) Great replacement motor
Reviewed By: Bob M. from Mendham, NJ ()
A.O. Smith 1.5 HP replacement pool motor was perfect fit. Purchased for about 1/2 the price that I found the motor anywhere in NJ and shipping time was better than expected.
Was this review helpful to you?
1 0
(5 out of 5 stars) Excellent replacement pool pump motor
Reviewed By: John B. from Merritt Island, FL ()
Cons: None
This is my second pump, the first for the pool works great after 5 years. . This pump was purchased for the spa system. Installation was easy, the fit excellent, enclosed instructions very helpful. Highly reccomend Inyo Pools for any parts.
Was this review helpful to you?
1 0
(5 out of 5 stars) Top Notch Motor
Reviewed By: Wayne C. from Raleigh, NC ()
Pros: Exact fit. Saved a ton of money replacing it myself.
Cons: None I know of yet. (3 months service so far)
My previous motor finally died of corrosion, and I found this replacement. It has a better finish, runs quieter and cooler also, at the same HP and RPM. Price here was the best also.
Was this review helpful to you?
1 0
(5 out of 5 stars) A.O. Smith 1.5 HP Round Flange Up Rate Motor
Reviewed By: Camille D. from Wakefield, MA ()
Delivered when promised. The man that installed it found everything needed and had no trouble putting it in. I also saved about $80.00 ordering it through inyo pools.
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Michael L. from Springfield, VA ()
Pros: Easy installation. Pump working well.
Installation instructions on your website were very helpful.
Was this review helpful to you?
1 0
(5 out of 5 stars) new motor works great
Reviewed By: Alexander B. from conway, AR ()
Pros: Excellent directions online
Cons: I would include in directions that the wrench to hold the spindle in place is 7/16"
My pool pump gave out after four years continuous use and possible lightning strike. I had the option of replacing the pump and motor for about $400 or just the motor for much less. I am not an electrical person, but after watching the video online of motor replacement, I decided to give it a try and save some money. The video was so good that the motor replacement took less than 45 minutes and it works great! In retrospect, my motor was probably beginning to fail about a year ago. Now the power is ideal: I can run my skimmer, pool vacuum, and automatic vacuum at the same time with excellent results.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Julian B. from Liberty Township, OH ()
Exact replacement - no issues. Fitted together perfectly.
Was this review helpful to you?
1 0
(4 out of 5 stars) Pump works
Reviewed By: Steve A. from Norwell, MA ()
Replacement of old pump went smootly and new pump works. Only a week so can say no more.
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Harold H. from Sevierville, TN ()
worked perfectly for my system and was delivered a day early. Thanks for your hard work and assistance.
Was this review helpful to you?
1 0
(5 out of 5 stars) Perfect match -- easy wiring
Reviewed By: Will R. from Overland Park, KS ()
Pros: Perfect fit
Cons: some written instructions would be nice
This unit matched up perfectly with my pump. The youtube vid was helpful in figuring out how it all came apart. So easy ... a caveman could do it!
Was this review helpful to you?
1 0
(5 out of 5 stars) Great pump at a great price
Reviewed By: Jeff R. from Albuquerque, NM ()
Pros: Durable and long lasting pump. Fairly quiet
Cons: Will not start telepathically.
This was, and still is the perfect pump for my system. Originally had a 3/4 hp that finally burnt out and decided to splurge on a bigger motor. A.O. Smith produces a consistent and long lasting motor. The other one I had in there has been there for a good 12 years or so, faithfully starting and stopping at each and every request and very quiet.
Was this review helpful to you?
1 0
(4 out of 5 stars) AO Smith Motor
Reviewed By: Chip from La Plata, MD ()
Pros: OEM replacement
Standard replacement for Hayward Super Pump- everything went together perfectly
Was this review helpful to you?
(4 out of 5 stars) Running smooth
Reviewed By: stones442 from Lockport, IL ()
Pros: nice and quiet
Was this review helpful to you?
1 0
(5 out of 5 stars) Worked perfectly, saves $$
Reviewed By: Karen S. from Orlando, FL ()
The pump motor fit and works perfectly. Included instructions were written in plain English which made for an easy replacement job. Don't forget to buy the replacement gaskets too. INYO got it here next day and was much less than local supply stores.
Was this review helpful to you?
1 0
(4 out of 5 stars) hayward pump motor
Reviewed By: Michael R. from setauket, NY ()
The pump/motor has been in service about two weeks now, and is running cool. This newer version comes with a grounding clip already afixed to the chasis, so no need to run, and axiliary grounding lug.
Was this review helpful to you?
1 0
(5 out of 5 stars) Great customer service!
Reviewed By: Kelly B. from Augusta, GA ()
Pros: quick service
Cons: none
The first pump motor we received was defective. Thanks the the great customer service from Sharon at extension 702, we received a replacement motor in minimal time. She was very curtious and helpful.
Was this review helpful to you?
1 0
(5 out of 5 stars) Excellent pump motor
Reviewed By: WhitL from Marietta, GA ()
This is a direct replacement for my 1-1/2 HP Hayward Superpump. Installation is very straightforward, and easy enough for a diy-er like me to do.
Was this review helpful to you?
1 0
(4 out of 5 stars) Easy to install
Reviewed By: Kerry M. from Deland, FL ()
Pros: Easy to install, exact fit.
Cons: None
Motor was an exact replacement and with the step by step directions was easy to install.
Was this review helpful to you?