How many hours per day should I run my pump?
Reply
There are many factors to consider; bather load, gallons of water, pump horsepower, type and size of filter just to name a few. A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals. In peak season, when it is the hottest, raising the run time to 10-12 hours per day will help to keep the pool clean and circulating during it’s time of heaviest use.
Reply
What is the difference between this variable speed and the Intelliflo VF please? Thx.
Reply
The main difference is on the high speed capabilities of the pump, the Intelliflo can ramp all the way up to 3 HP where the SuperFlo can go up to 1-1/2 HP. For most pools the 3 HP is overkill and you really never need to go above 1-1/2 HP. If you have a standard pool 25,000 gallons or less and no crazy water features then the SuperFlo would be fine.
Reply
What are the stats on this pump? HP etc. Does it come in a 1 HP max?Thx.
Reply
You may view the stats on this SuperFlo VS within the SuperFlo VS Data Sheet. The SuperFlo VS is only available in a 1-1/2 HP max HP.
Reply
I am currently running a Hayward Northstar 2 HP pump into a 2 inch line with self cleaning pop ups in about a 12-14,000 gallon pool with an Aqua Link remote control
I would like to switch to a Pentair Variable speed. Can you can you tell me what size pump I need to perform slightly better than my current setup
Reply
Hi Wayne, The Pentair IntelliFlo Variable Speed (011018) would be your best option.
Reply
All my water lines are 1 1/2"
Is that ok for this pump?
Reply
Hello, The Super Flo VS pump has unionized fittings (1.5" internal slip and 2" external slip), meaning it will fit with the 1.5" piping you currently have.
Reply
Hi, I wanted to get the Pentair intelliflo vs pump. What do I need for electrical power to run that pump. Thank you , Barb
Reply
Hello barb this unit Accepts 99-253V, 50/60Hz input power. However, Code requirements for electrical connection differ from country to country, state to state, as well as local municipalities. Install equipment in accordance with the National Electrical Code and all applicable local codes and ordinances.
Reply
I am replacing a Pentair Whisper Flow 1 horse pump and have a 35,000 gallon unground pool. Which Pentair variable speed pump would be the best replacement?
Reply
Hello, Gene. I best recommend using the Pentair IntelliFlo i1 Variable Speed Pump MODEL#011008. The IntelliFlo i1 pool pump provides all the great features that have made our standard IntelliFlo pumps the best-selling industry standard, but is engineered to limit the flow to the equivalent of a 1 hp WhisperFlo® pump.
Reply
I manage a HOA pool that is 25' by 50' 55000 gal. I am running a 2 hp super pump and would like to switch to the variable speed. What pump do I need for this size pool? Also I have 2" connections.
Reply
Hi James, We will need to know the model of the pump you have of the "feet of head" of your pool to confirm if the Speck Badu EcoMV (2072266213) will provide adequate circulation.
Reply
I have the 342001 (installed 3/29/16), yesterday I came home and the control panel was on, and in turn the pump would not turn on. Tests have been done. The pool light will come on (same sub-panel) and electricity has been tested on the pump. The pump is getting juice. I've tried + - 1 buttons. And other combos. Any suggestions?
Reply
Hi Doug, Check to see if the motor shaft spins freely and or check if impeller is clogged. If you have checked and both are okay then you will need to contact Pentair at 1.800.831.7133 to set up a warranty claim if the pump was installed by a authorized technician.
Reply
Hi, my current pump is whisperflo 1 hp with 1.25 SF, which two speed or variable speed pump should I get?
Thanks.
Reply
The dual speed motor is the B2980T, variable speed is the ECM16CU, or the B981 in combination with the T10101R (VERIFY VOLTAGE) It is best recommended to replace the Tune Up Kit at this time with the GOKIT32 or GOKIT32SALT. You may also, view the WFDS-3 that requires the installation of the T10101R (Verify Voltage). InyoPools offers our own product line under the PureLine Pool Pumps if you would like more information to converting your pump to a PureLine, please contact us at 1-877/372-6038.
Reply
I currently have a 1/2 Hp, 115v, Wfe-2 pentair pump installed in my 30,000 gal pool. It has 1-1/2 in piping with a single pool return and single jet. Would the superflo vs be a good pump for my pool? It has a salt water generator and
Reply
Hi Steve F, The Super Flo VS pump can be used as a replacement for the WFE-2 pump based on the performance data of the two pumps. The plumbing will have to be redone.
Reply
I currently have the 1HP Sta Rite P2RA5E 181L pool pump for my 33,000 gallon pool. I also use 1 1/2 piping with a 48 sq foot DE Pentair filter. Can you please confirm that the Pentair VS PUMP VAR SPEED W/ TIMER SUPER FLO PUMP 115/230V - 342001 would be a good replacement for me to use?
Reply
I don't see those being in available much longer, which means it will be hard to find parts for it in a few years when you need them. I would recommend the Pentair IntelliFlo which has a much greatest track record. Plus I don't see that pump going anywhere anytime soon.
Reply
I recently upgraded from old 1HP pump to Pentair SuperFlo VS Variable Speed 1.5HP 115/208-230v. My in-ground pool (~15,000 gallons) has Hayward C12002 Star-Clear 120sf filter. Pump runs from 12am to 8am at step 3 (2200 RPM).
Each time the pump starts up (12am), the return jets blow out dirt and cartridge filter fiber. This seems to only happen then. Not a problem during quick clean. What do you think is the problem and how should I go about fixing it (already tried cellulose fiber)? THX!
Reply
Good Afternoon Chris, Sounds like you need a new filter element. How long has it been since you replaced your element. The cellulose fiber could be your problem if your using to much once the filter is clogged. You will have blow back. If the filter element is old replace it. If it is not old clean it and quit using the cellulose.
Reply
I have an a. O . Smith model s48b73a03 in ground indoor pool. Im looking to change to a variable speed. Is this the best choice?
Reply
What is the model of the pump you are replacing, the model number you provided is for the motor? That motor goes to multiple different models of pumps.
Reply
I have an a o smith motor model s48b73a03 with pump jwpa5dl-2a2 is this the best variable speed pump to replace with
Reply
Hi, Amanda. The Hayward Super Pump VS Pump - SP26115VSP is the best variable speed pump that will replace your JWPA5DL-2A2 pump.
Reply
I am building a 10000 gallon lap pool average depth 4.5 feet, with solar heating 12 feet up on the roof. Would this pump be suitable for this application or would you recommend Intelliflo. Also, what cartridge filter would your recommend with this pump.
Reply
What is the distance in feet from where your pump is going to be to where the skimmer(s) are going to be. This is so I can calculate the flow rate so I can proper size both the pump and filter.
Reply
I have a 22000 gal fiberglass pool , what size sand filter will work with a super flo vs 342001 pump
Reply
Hello Van- The filter I would recommend for the VS PUMP VAR SPEED W/ TIMER SUPER FLO PUMP 115/230V 342001 is the Triton II TR100 Filter Side Mount 30" Tank - 140210.
Reply
My pool is 20,000 gallons and I currently have an old Pentair Whisperflo 1HP pump with a Pentair FNS Plus 36. I also have solar panels installed on my garage roof. What would you recommend to replace both the pump and filter. Is there a pump that would qualify for the DWP rebate? Also, I would like to get a quiet pump?
Is this a quiet pump, Pentair 342001 SuperFlo VS Variable Speed Pool Pump, 1 1/2 Horsepower?
Reply
The fns plus 36 would be a great filter to still with and the SuperFlo variable speed pump would qualify for the rebate.
Reply
I have an a o smith motor model s48b73a03 with pump jwpa5dl-2a2 is this the best variable speed pump to replace with
Reply
I would say that this is a very good option for replacing your current pump with a variable speed one.
Reply
Hi, I currently have a WhisperFlo WFE-6 1.5 HP pump. Bearings are making noise so time to replace with a Variable Speed model.
Pool and spa combo all at same level. Freeform 33 x 16 without spa max depth of 8 ft
I will have it installed by a certified installer so I can qualify for DWP Rebate. Which model would you recommend? I want to be sure I will have the 3 year warranty.
Reply
Hi, Peter. The Superflo VS Pump would not be a suitable replacement for a Whisperflo pump. The Intelliflo VS Pump - 011018 is what I'll recommend. The Superflo and Intelliflo VS pump comes with a 2 year manufacturer warranty when professionally installed.
Reply
Best replacement pump for central Ohio?Have a 1.5 Hayward super pump sf 1. total of 138' of returns (three lines) 1 1/2". Pentaire FNS 60 filter, 16x32x4 total 15300 gallons, average feet in head - 46. Does 32GPM sound correct?1 hp pentaire VS replacement? Dual speed more cost effective?Which pump and motors suggested? Currently110 volts, would like to use existing electrical supply lines, Larger savings going to 220V?
Reply
Hi, ScottR. Giving the info provided this variable speed pump will work, however, you may not be able to operate the pump below 2700 RPM giving the three return lines, 138' of pipe and a 46' FOH. If you upgrade the electrical to 220 volts it would be cheaper to operate.
Reply
Hello,
Will this pump work as a direct replacement to my Hayward sp15931FP pump/sp1520z1esc motor set up. Want to go variable speed to gain the most energy savings. Filter is a Hayward s210t for 18,500 gallons of water with salt generator and 10 feet each way of head connected to hose and 1 -3 way valve.
Reply
Hi, Manny. The Superflo VS Pump at full speed will generate a flow rate that will exceed the flow rate of the S210T filter. I would recommend the Hayward Super Pump VS Variable Speed Pump - SP26115VSP.
Reply
I have an 18000 gal pool with a 420 sf cartridge filter, salt system and solar panels. My current pump is a whisperflo 1.5hp 1.47sf pentair and i want to replace it with your pentair vs 342001. All pipes are 2". Will this vs pump work effectively?
Reply
Hi, Bob. The Superflo VS Pump is not a good replacement for the Whisperflo Pump. You can use the IntelliFlo Variable Speed - 011018 will be sufficient.
Reply
We are thinking of replacing our single speed 1.5 hayward pump with the Superflo VS. We currently have a separate booster pump for our Polaris pool sweep. Can we control the Polaris thru the Superflo? Can an external freeze guard be connected to the Superflo also? Thanks
Reply
Hi, MAM. A Booster Pump can not be controlled or nor can an external freeze protection system be used with the Superflo VS Pump.
Reply
Would this be a good pump for 30k gal pool, with 3 inlets of 1.5 inches and average of about 35ft head, and 113 gpm cartridge filter?
Reply
Hi, Reegee. Yes, this pump will provide adequate water circulation for your pool based on the info provided.
Reply
Hello.
I have a 11,000 gallon in ground pool with a Sta-Rite Posi-Clear filter Model PXC125. Would the Pentair 342001 pump be a good choice or would I have to replace the filter?
Reply
Hi, Bert. You can use this Superflo VS Pump with a Sta-Rite Posi-Clear filter - PXC125. The flow rate must not exceed 125gpm.
Reply
Hello, can I use the Pentair 342001 VS Superflow to replace a Sta-Rite Max-E-Pro Series P6e (Ae100ghl 2hp; P6E6G). Also, would I still utilize the Easytouch Intelliflo now hooked up? I'm worried about how to utilize the "freeze protect" function. Many thanks for your counsel!!
Reply
Hi, Joe. You can if the Superflo VS Pump will meet your pools need. The Sta-Rite Max-E-Pro Pump is a higher performance pump than the Superflo Pump and maybe oversized for your pool. You can use our How To Size a Pool Pump guide to determine if the Superflo VS Pump will be able to meet your pool needs.
Reply
Hi, I have a 30,000 gal in-ground, no spa, no heater in southern California (SCE). Currently running a Purex Triton Wisperflow -1hp. 2” plumbing using a Purex Triton 2000, 48sq ft. DE filter. Thinking about upgrading to a variable speed. Looked at replacing with Pentair 342001 VS Superflow or just replacing motor with V-Green 165 variable speed motor. I have rebuilt pump once and I will do all the work myself. Your thoughts?
Reply
As long as the pump housing is in good condition, and you have not had any issues with flow or suction with the horsepower rating there, then it sounds like an ideal upgrade to a variable speed motor.
Reply
What is the voltage of this pump do I need a 230V to run it why is it stated 115/230 I only have a 120 at my pool equipment room
Reply
This pump can be used with either 115 or 230. If you have 120 going to your pump then the 115 setting is what you would use on the pump.
Reply
I have a single speed Sta-Rite model number MPRA6E-147L running on 230v and I just added a Jandy heat pump JR3000TR to my system that I bought from you. Based on the information I know, my TDH is 30 and my sand Filter is capable of handle about 63 GPM. The current pump is 1hp and the piping system is 2in. I want to upgrade to a variable speed pump where my connection are the same to the current pump. Do you have any recommendation?
Reply
Hi Jose, Unfortunately, there is not a drop in replacement pump for your MPRA6E-147L pump. You do have two options... Option #1 is to replace your pump with the 1.65 HP PureLine Prime Variable Speed Pump which would require some re-plumbing. The other option would be to replace your motor with the Century 1.65 HP Variable Speed Motor a Dyna Glas 1.5 HP Impeller and a Dyna Glas Seal kit. The second option would continue you to use your current pump housing so no re-plumbing would be required.
Reply
It appears that to qualify for the $50 rebate that you list here, Pentair requires both that the product be purchased at a brick & mortar location as well as professionally installed. Is that true?
Reply
Hi, David. In order to qualify for the rebate, the pump must be purchased and professionally installed between April 1, 2018, and September 30, 2018. Must redeem within 30 days of purchase online or by mail.
Reply
I am replacing single speed pump wired for 115v with the Pentair Super Flo VS which takes either 115v and 230v. Is there any reason to rewire for 230v to get the max energy efficency of this pump? If so how much efficiency would I lose at the lower voltage?
Reply
I curently have Hayward 2 speed 3/4HP pump can it be replaced with the VS PUMP VAR SPEED W/ TIMER SUPER FLO PUMP 1.5HP 115/230V - 342001
Reply
Yes, the maximum strength of this variable speed pump will umbrella your current motor specifications and can always be dialed down to match what you currently have if you need to. Just keep in mind that if you have an automation system that you may need a communication link to be able to control that pump from your panel.
Reply
Replacing a 1 hp whisper flow # 7-177450-03 motor . Is this a replacement vs the 011018 pump?
Reply
Can I replace my pentair WFE-28 with the Pentair Superflo VS
Reply
Hi, Robin. It's possible based on your pools Total Dynamic Head (TDH) and the required flow rate..
Reply
No way for me to figure that out ... it’s a 15,000 gallon In ground pool with a connected hot tub. I think the pipe is 2 inch.
Hi Robin, In normal pool applications the Total Dynamic Head will be around 50' based on this number the SuperFlo VS will be outputting 70 GPM on the high speed where your WhisperFlo WFE-28 would be outputting about 120 GPM at 50' of head. For general pool filtration the 70 GPM should be more than enough for a 15,000-gallon pool, the only thing that would be a question mark is the spa jets. You may have the higher HP on your pool so that you can adequately power your spa jets. Depending on the type of spa jets you have determines your flow needs. Spa jets normally need between 6 GPM - 20 GPM based on the model. Let's say you had 10 jets that require 10 GPM each then you would need a pump that could output a 100 GPM and the 70 gpm of the SuperFlo VS would not be adequate. I hope this helps.
Reply
Can this replace a Jandy PHPF1.0 pump
Reply
Yes, this pump could replace the Jandy PHPF1.0 pump. Our recommendation would be the PL2605 PureLine Prime 1.65 HP Variable Speed Pump, the PureLine Pump has been a great pump for us. The plumbing ports on either of these pumps are not in the exact same spot as your current pump so you will have a little re-plumbing.
Reply
I currently have a pool pump with Century motor (USQ1202) with 2 HP and SF=1.10 and total HP =2.20. Will the Pentair superflo variable speed pump be a good replacement? I believe the Pentair superflo has 1.5 HP only but the total HP is also 2.20.
Reply
Hi Wes, The Total HP or True HP is the number you will want to compare. Since your current motor has a True HP of 2.2 and this SuperFlo Variable Speed also has a True HP of 2.2 then you will be fine using this as a replacement.
Reply
Hello. I have a Jandy HHPLUS Series pump and Jandy Model PHPU2.0 HP Motor with 2" connectors. Do you believe that this SuperFlo VS Pump could be a replacement for that pump? If not, what other options do I have for VS speed pumps? Thanks for your time.
The SuperFlo VS would be an adequate replacement, but the Pureline Prime 2.7 VS would be the best buy for the money in this range of pumps.
Reply
We have a 25,000 gal pool - would this be a pump you'd recommend?
Reply
Hi, Rosin. It's possible, we will need the Total Dynamic Head (TDH) of your pool to confirm.
Reply
I would like to get a Drop in replacement for jandy stealh pump 1.5 hp for a salt water pool,, would like a variable speed pump, I think, any suggestions. 18x32 kidney shaped pool.
Reply
This is a great choice for a replacement pump/motor, it will need some minor modifications. Check for Manufacture and power company rebates too!
Reply
I have a 23000 gal inground pool with spa and is currently using a Sta-Rite 2HP P6E6G-208L will this SuperFlo VS Variable Speed Pump 342001 be an adequate replacement pump to be CA compliant?
Reply
Hello, I’m looking to replace my current single speed pump with a variable speed pump. My pool is somewhere between 20,000-25,000 gallons, and the average TDH is 170/3=57’. I have a connected hot tub as well. Also, my filter is a Pentair Quad 60-DE filter, rated at 120 GPM. Is this the right size pump for my situation? If not, what would you suggest? Thank you so much!
Reply
Hi, Steve. This pump will be sufficient based on the Total Dynamic Head (TDH) of your entire pool. To properly calculate the head, use our How Do I Calculate Feet of Head for My Pool? or How To Measure Total Dynamic Head With Gauges guides.
Reply
Pump has converted to external Control only so program is disabled. How do I start the pump?
Reply
You would use the external control that it is now hooked up to.
Reply
YOUR START/STOP BUTTON DOES NOT WORK? LOWER LEFT CORNER
Reply
You would use the external control that it is now hooked up to.
Reply
Turn off the Start/Stop light then hold the button till the External control light goes off. Mine came in External mode when purchased and had the same problem.
Reply
I have a Reliant BC2748 pump with the Reliant RLC BC3103C filter. My pool is a 15000 gallons. I'm considering replacing my setup with this pump and either a 100 or 150 sqft Pentair Clean and Clear RP. Will this be a good replacement? Which one do you recommend 100/150? I also got a Intellichlor IC20 that I will be installing.
Reply
150 turns over 72,000 gallons of water in 8 hrs 100 turns over 48,000 gallons of water in 8 hrs Both are great choices with VS pump you may like the 150
Reply
purchase your model#342001 and would like to know if there is a way I could get my pump to have a stronger volume of water coming out of jets and waterfall? What settings would be the best for my issues.
Reply
So there is no one way to answer that as each pool is different, however, this pump has a total HP of 2.2 so if this pump exceeds your current pump max HP then all you would need to do is slowly raise the RPM's to test which setting best suits your application.
Reply
Can the Pentair 342001 work with an Aqua Rite electronic pool chlorinator control unit? In other words, can the pump's timer accept an electrical connection from the chlorinator control unit and control that unit as well ?
Thank you.
Reply
I inherited a SUPERFLO WITH FRIED CONTROLS. iS IT POSSIBLE TO RUN THE MOTOR OR DIRECT 220 VAC
Reply
Hi, Doug. Unfortunately, we're unable to confirm since we do not have knowledge of how the motor is wired internally.
Reply
Ive ordered this pump (haven't received yet) but was looking thru the installation guide......regarding wiring, I currently have 220V with 12/3 wire. One black(load), One red(load), One white(common/neutral), and one green(ground)..... I notice in the picture that the pump panel only has ground, L1 and L2....how should I wire this one up? What do you do with white????
Thanks
Reply
As long as the two leads are carrying the voltage then you can just cap off the neutral line.
Reply
I am replacing a Speck Model 433-IV pump with a 3/4 hp motor. Will this be a good switch in a vs option? Also, I previously had a pool side Polaris cleaner with booster. Will this be able to run that without the booster pump? Thanks
Reply
Hi. This SuperFlo VS Pump will be able to be used as a replacement based on the Total Dynamic Head (TDH) of your pool. If your Polaris cleaner requires a booster pump, you will need to keep it.
Reply
Hi. I currently have a Pentair SuperFlo 340039. Does this SuperFlo VS have the same dimensions for PVC hookups? I believe that would make it an easy drop-in, versus having to re-pvc anything? Please let me know. Thanks.
Reply
Derek, yes, the SuperFlo VS Variable Speed Pump 115/230V - 342001 has the same dimensions as your existing SuperFlo 1.5 HP Single Speed Pump - 340039. It would be considered a "drop-in" replacement.
Reply
Ref DIY Pentair Variable Speed Pumps will it void a warrantee?
Reply
Hi, Steven. If this pump is NOT installed by a qualified installer, it will only be warranted for 60 days from the original date of installation. If installed by a qualified installer and submitted with the proper documents, it will be warranted for 2 years. If more info, review the Pentair's Product Warranty Information.
Reply
What is the total length of this unit (Pump & Motor) front to back? I have a Hayward single speed Super Pump on a 26K gallon in ground with 1.5” pipe and a TDH of 40. Is this a suitable variable speed replacement?
Reply
Hi, Tom. The length of this pump is 22.56". Yes, this Pentair SuperFlo Pump is a suitable replacement.
Reply
Can Pentair SuperFlo VS pump connect to the Hayward AquaPlus controller? Thanks.
Reply
Hi, Hien N. Unfortunately, the SuperFlo VS and the Hayward AquaPlus software are NOT compatible. You can use the Hayward Super Pump VS Variable Speed Pump 230V - W3SP2603VSP.
Reply
Hi, I have a 6 month old Jandy 3/4 horsepower, single speed pump fitted to my new pool. I have just begun to realise how much it is costing me, can I replace it with this pump? Or another Pentair VS pump? Thanks Al
Reply
Hello, I will need the full model number from the Jandy pump wet-end to correctly suggest a replacement VS pump. The change from single speed to a VS pump should be reviewed by a professional first to verify the reduced flow rates of the VS pump will be a sufficient change for the significant cost to operate at lower speeds. We offer Variable Speed Pool Pump Buying Guide http://www.inyopools.com/blog/variable-speed-pool-pump-buying-guide-2/ for some help, however, knowing the current model is definitely a plus to best recommend for the transition to a VS pump.
Reply
I have a Pentair Triton II filter. I am assuming this pump will work well with it or do i need a larger size HP? We have about 26K gallon in ground pool and Jacuzzi that waterfalls into the pool. I am replacing a 2HP pump that is about 6 years old.
Reply
The SuperFlo VS Variable Speed Pump 115/230V - 342001 most likely will not be strong enough to provide adequate flow to the features mentioned. If you could provide the current pump model number that is very helpful to suggest a variable speed pump for the transition. There different types of pumps on the market designed to provide certain flow rates and types of flow. The IntelliFlo i1 Variable Speed Pump - 011059 may be a better choice to review for this type of application, however, it is best to also verify the maximum flow rates on the filter before ordering a pump.
Reply
My pool holds about 23000 gallons of water. The pool filter is a Pac-Fab (D.E.; 7 full + 1 half; 48 sq ft). And my existing pump is a Centurion for PAC•FAB (Challenger; P/N 35-5335; PART 8-168452-20; RPM 3450; SERIAL BE4-141; HP ---). Is SUPERFLO VS too big for my pool?
Thanks!
Reply
The SuperFlo VS Variable Speed Pump 115/230V - 342001 is not suggested to transition to from a Challenger. The Challenger is a heavier duty-specialty pump. Your motor number confirmed to have a total HP of 1.25 and voltage options of 230 or 115V. The Waterway Power Defender 165 Variable Speed Pool Pump 1.65 HP 230V - PD-VSC165 is the pump I recommend for proper flow rates, this pump only operates with 208-230 Volts. If you have 110/115-120V you will need to contact an electrician to have them run the line for 208 or 230V.
Reply
I have an early Pentair IntelliFlo Pump, 3 HP, 174 gpm (P/N 353011) and am having lots of problems with maintaining maximum rpms as it keeps cycling off and on. I'm wondering if the VS Pump 342001 would be a good replacement. The pool is a 20,000 gallon salt water pool with a chlorinator. Any thoughts or recommendations would be greatly appreciated. Thank you.
Reply
Hi Randy, there are a few variables that need to be considered when sizing a pool pump. Here is a guide that we put together called "How to Size a Pool Pump for Your In-Ground Pool" that should assist.
Reply
I have a Sta Rite Max E Pro - single speed. would this be a reasonable VS replacement? What other items will I need to do make the swap?
Yes this would be a good replacement for your Max E Pro in the photo. Nothing major for the swap, you would just have a little re-plumbing. Also note that the Max E Pro could be wired 115v or 230v where this pump can only be wired 230v.
Reply
How many gallon pool with this pump be efficient on? There are no waterfalls or jacuzzi areas
Reply
Good afternoon Dwayne, The average-sized pool for 342001 is around 20,000 gallons. I have attached a link to sizing a pump for your pool to help you further.
Reply
I have an in ground pool - the volume is 23000 gallons I would like to match this pump with a cartridge filter. the piping is 1 1/2, what Cartridge filter is best.
Reply
Hi Charles, so there are a few variables to consider when sizing a pool filter. Here is a guide that we put together called "How To Size a Pool Filter" that should help with that.
Reply
I have a 30,000 gallon pool with a master pools cleaning system (10 cleaning heads) and a built in hot tub (separate booster pump and air blower), would this pump be a good replacement for the current 2hp sta-rite max e pro? I’m not sure how the vs would impact the master pools cleaner
Reply
Hi, Casey. Unfortunately, this SuperFlo VS Variable Speed Pump 115/230V - 342001 will not be a suitable replacement. Before going to a variable speed pump, calculate the Total Dynamic Head (TDH) of your pool to make sure that a variable speed pump will meet your pool needs and reduce operating cost. Otherwise, I would recommend the Waterway Power Defender 270 Variable Speed Pool Pump - PD-VSC270.
Reply
For a 15k - 16k gal. pool, with a pentair variable speed pump, what would be the most energy efficient settings to run the pump? At the present time 2hrs at 2600 rpm, 4 hrs at 1750 rpm, 2 hours at 2400 rpm.
Reply
Hi Christopher, so there are a number of variables to consider when trying to set up your variable speed pool pump for the most efficient usage. Here is a guide that we put together called "Best Setup For Variable Speed Pool Pumps" that should assist.
Reply
New pool installation... 12,000 gallon fiberglass 14'x35', TDH approx 35-40. Want to use a Pentair Clean & Clear 150 filter with a Hayward Aquarite 25K salt chlorine generator. Is this pump sufficient or should I go with the 011018? Do you see any interface/programming issues; pump to Aquarite? Recommendations? Thanks!
Reply
Yes, the SuperFlo VS Variable Speed Pump 115/230V - 342001 can be installed at 35-40' TDH with the Clean & Clear RP Cartridge Filter 150 sqft. - 160355 and with the use of a W3AQR9. An external timer is needed for the salt system. It will not be wired directly to the pump. http://www.inyopools.com/Blog/psc-ep-90-need-timer-salt-system/
Reply
I currently have a Sta rite pump 343001 that does not work. Can I replace it with a 342001 pump?
Reply
Peter, Yes, you can use pump # EC-342001 as a replacement for the StaRite 343001.
Reply
Hello - I have a Hayward superpump with 1.5" piping. Can I replace it with this? I am hoping to avoid the electrical swap out as the Hayward is 115v and so is this unit. Thanks.
Reply
Hello Aaron. The Pentair SuperFlo VS 1.5 HP VS Pump can accommodate 115VAC or 208VAC - -230VAC.
Reply
I have a Sta-Rite Dyna-Glas single speed pump that just died today after 18 years. 25K in-ground pool. (1.5 HP, 115/230, ports are 2" internal NPT ) Looking for a variable speed pump...worried about so many pumps being back-ordered. Suggestions please?
Reply
We have this pump in stock. If you are replacing an existing pump you want to make sure that your pool filter can handle the GPM of the pump. You can use the performance curve on the pump page to get the proper GPM. Your Filter should have a GPM rating.
Reply
will this replace the wfe 26 pump which is no longer being manufactured
Reply
Hello Stanley. The Pentair Superflo Variable Speed Pump model EC-342001 is a compatible replacement for the Whisperflo model WFE26.
Reply
Pool is 20,000 Gal. Use solar roof panels to heat my pool. Want to replace old Pentair vs..3050, with a new pentair superFlo. Will this pump lift the water to my roof ? Also need the Pvc size to use and the size of the unions. Also do unions come with pump? same info for the pentair InteliFlo vs. pump.
Reply
Hello William. The Pentair SuperFlo VS 1.5 Variable Speed Pump Is a compatible replacement for the Pentair VS 3050 if your solar heating panels are installed on a single-story roof. If the solar heating panels are installed on a two-story roof then the Pentair IntelliFlo would be the appropriate replacement. The SuperFlo VS comes with union connectors for 1.5" or 2.0" plumbing. The IntelliFloXF comes with union connectors for 2.5" or 3.0" plumbing. https://www.inyopools.com/Products/03500018077523.htm#parts IntelliFloXF® Variable Speed Pool and Spa Pump - EC-022055
Reply
one of my customers has a Whisperflo Model WF-28 what should we replace it with..
Reply
Hello Jim. The Pentair Poop Products Superflo VS 1.5 HP Variable Speed Pump would be an excellent replacement. The VS Pump will operate with reduced electrical costs and complies with Federal Regulation, Energy Conservation Standards for Dedicated-Purpose Pool Pumps, which went into effect July 19, 2021. SuperFlo® VS 1.5 HP Variable Speed Pump - EC-342001
Reply
when I loose power my clock does not keep time. is there a internal battery that needs to be replaced? thank you.
Reply
Thank you for contacting Inyo Pools, According to Pentair tech department as the pump ages, it struggles to keep the programming.
Reply
I have a Century 165 VSP attached to an old system. See the attached pix as reference. The system is 15yrs old and the VSP is about six yrs old and is rusting badly. Rather than replacing the VSP motor, I thought it best to replace the entire system. Can you suggest a replacement? The pool is about 13k gallons and has a waterfall which requires me to run the VSM at 1800RPMs. Hope this helps/
Reply
Hello Thomas. The Pentair Pool Products SuperFlo VS 1.5 HP (2.2THP) model EC-342001 would be an excellent variable speed pump to replace the current system. Pentair SuperFlo® VS 1.5 HP Variable Speed Pool Pump - EC-342001 At lower RPMs the SuperFlo still has the ability to support pool and waterfall circulation. SuperFlo's ease of programming will facilitate adjusting water flow to meet requirements.
Reply
How to use timer to change the running time?
Reply
Hello. The Pentair SuperFlo VS Pool Pump has an internal clock - the time is displayed on the LCD screen. The daily run time/speed/duration programming is based on the clock setting making it necessary to set the clock first. Attached please find the SuperFlo VS INSTALLATION AND USER’S GUIDE Please note sections - Setting the Clock (page 7) & Custom Schedules (page 8)
Reply
I currently have this pump Pentair SuperFlo Variable Speed. I'm looking to find an inground DE Filter compatible with this pump. My pool is 16,000 gallons. What do you recommend?
Reply
Hello Stephanie. The FNS® Plus 36 DE Filter with the 1 1/2" Multiport Valve or 2" Multiport Valve (depending on plumbing size) are compatible with a 16K gallon pool and the SuperFlo VS. The Hayward ProGrid DE Filter 36 Sq Ft with the Vari-Flo Valve 1 1/2" or Vari-Flo 2" are also compatible. Combining comparable equipment from different manufacturers does not negatively impact their performance or pool water circulation.
Reply
Need to replace a Pentair superflo 1.5 hp pump. We have a 7000 gal. Inground Fiberglass pool, sand dollar sd80 sand filter, and propane heater. One main drain, two returns, one skimmer. Please recommend the best two or three pumps sized for our pool. Thanks
Reply
Hello Robert. The Department of Energy Energy Conservation Standards for Dedicated Purpose Pool Pumps, enacted July 2021, discontinued the manufacturing/marketing of single-speed inground pool pumps in the United States in lieu of variable speed pool pumps. Inventories of single speed and dual speed pool pumps have become increasingly scarce. The Pentair SuperFlo® VS 1.5 HP Variable Speed Pool Pump - EC-342001 would be an excellent drop-in replacement. The Hayward Super Pump VS Variable Speed Pump 230V - W3SP2603VSP is a compatible variable speed replacement. The Pentair WhisperFlo 1HP High Performance Pool Pump - EC-015583 (single speed) has very similar performance data to the SuperFlo 1.5HP.
Reply
On your website it indicates item number EC-342001 Pentair VS pump is in stock. Can you please confirm quantity onhand prior to order? Thanks!
Reply
Hello Aron, unfortunately this pump currently is not in stock however you can add yourself to the "notify me when in stock" from the items page.
Reply
Replacing an old single speed 1.5hp Hayward Super Pump on 33k gal inground pool approx 40’tdh. Is this pump a good choice? Also would it be able to handle a modest spa added in future? Thanks
Reply
Hello Erik. Comparing the Performance Data @ 40 ft TDH for the Hayward Super Pump @ 3450 RPM - 78GPM and Pentair SuperFlo VS @ 3450 RPM - 83GPM the two pumps are very similar. The SuperFlo VS is an excellent replacement variable speed pump for the Hayward Super Pump. The SuperFlo VS would have the ability to accommodate a spa with a spillover feature. The volume of the spillover would be determined by the pump's RPMs. Pentair SuperFlo® VS Hayward Super Pump Reference Performance Data - Product Detail Section
Reply
