?     Asked on 7/20/2017by bj

what is the difference between this and the b2858 motor?
 Reply

A  Answered on 7/20/2017 by InyoPools Product Specialist Joe S.

PL2854 is an Uprated motor B2858 Full Rate How To Understand True Pump Horsepower - Up Rated vs Full Rated Link attached
 Reply


?     Asked on 4/11/2018by billy owens

Is this motor reversible if not what is rotation?
 Reply

A  Answered on 4/12/2018 by InyoPools Product Specialist Lennox H.

Hi, Billy. This motor is not reversible. The rotation is CCW from the shaft end.  
 Reply


?     Asked on 5/29/2018by Greg

I purchased this motor and no paper work came with it. In particular, is there warranty information? Do I need to register the pump with the manufacturer?
 Reply

A  Answered on 5/30/2018 by InyoPools Product Specialist Lennox H.

Hi, Greg. No paperwork is required to be completed. Contact Inyo Pools if there is an issue with the motor for warranty purposes. 
 Reply


?     Asked on 6/14/2018by Inyo Visitor

Change motor only d83hf pump
 Reply

A  Answered on 6/14/2018 by InyoPools Product Specialist Megan C.

Please view our How to Read a Motor Label Guide https://www.youtube.com/watch?v=aN6CS3HBLmw&t=34s to determine the correct motor. If you need further assistance you may contact us at 407.834.2200 or use our service link at https://secure.inyopools.com/Support/SupportRequest.aspx to upload images of the label. 
 Reply


?     Asked on 6/24/2018by Inyo Visitor

Is this pool motor a good replacement for the marathon c1246?
 Reply

A  Answered on 6/25/2018 by InyoPools Product Specialist Hector F.

Yes, this motor is a compatible replacement but maybe a wider version so the original would actually be the model USQ1152
 Reply


?     Asked on 7/5/2018by Mark

Will this replace my pac fab challenger 1.5 HP... P/N 35-5340
 Reply

A  Answered on 7/5/2018 by InyoPools Product Specialist Hector F.

Yes, this would be a compatible replacement motor for the model 35-5340 motor. 
 Reply


?     Asked on 7/6/2018by MARV LEIBMAN

will this replace century motor p/n 75234 & ultra-flow pump
 Reply

A  Answered on 7/6/2018 by InyoPools Product Specialist Lennox H.

Hi, Marv. Yes, this PL2854 motor will replace P/N 75234 operating an Ultra-Flow Pump. You will also need to get the Ultra Flow Tune Up Kit - GOKIT20
 Reply


?     Asked on 7/23/2018by stavro

Hi, is this motor a good replacement for Century B2983?
 Reply

A  Answered on 7/23/2018 by InyoPools Product Specialist Hector F.

If you are looking for a single speed Pureline replacement motor then the model would be PL2859.  
 Reply


?     Asked on 9/1/2018by Michael Vener

What kind of thread the motor shaft has?
 Reply

A  Answered on 9/1/2018 by InyoPools Product Specialist Lennox H.

Hi, Michael. The motor shaft has UNF - unified national fine threads. 
 Reply


?     Asked on 9/1/2018by Michael Vener

I would like to know the inside and outside thread diameters on motor shaft.
 Reply

A  Answered on 9/3/2018 by InyoPools Product Specialist Lennox H.

Hi, Michael. The external threads are 1/2-20 UNF and the internal threads are 1/4-20 UNC. 
 Reply


?     Asked on 9/9/2018by Inyo Visitor

Will the 1.5 motor,part PL2854 work as a replacement motor for the Pentair Challenger, # 34-6206 How long would it take to get this part delivered?
 Reply

A  Answered on 9/10/2018 by InyoPools Product Specialist Hector F.

Yes, this would be a suitable replacement motor and motor orders on the average take approximately 3 business days to be delivered. 
 Reply


?     Asked on 9/16/2018by Steve

Will this motor replace the 1 1/2 hp motor on a Pentair Superflow model 340039 pump ?
 Reply

A  Answered on 9/19/2018 by InyoPools Product Specialist Hector F.

As long as you are replacing the original motor model that came with this complete pump then yes this is a compatible replacement motor. 
 Reply


?     Asked on 11/5/2018by Scott Tait

what is your shipping time to florida ?
 Reply

A  Answered on 11/5/2018 by InyoPools Product Specialist Hector F.

So these actually ship out of Florida so 1-2 business days on average. 
 Reply


?     Asked on 11/29/2018by Inyo Visitor

Is this a good pump to replace a Century Motor Model C48L2PA105C5 SER

 Reply

A  Answered on 11/30/2018 by InyoPools Product Specialist Hector F.

Technically this motor is wider at a 56 frame so it may not be able to rest on the motor base if you currently have one. Other than that the specs match or you can use the model USQ1152 which is what I would recommend.  
 Reply


?     Asked on 1/3/2019by Frank

I have a Challenger motor that needs replacing. I can’t tell if it’s 1.0 or 1.5 hp. Can I use this motor as a replacement?

 Reply

A  Answered on 1/3/2019 by InyoPools Product Specialist Kevin G.

Hello, thank you for contacting Inyo Pools. Unfortunately, there is not enough information on the motor label to get the correct one. To get the right impeller, could you please send me the number that is on your impeller?
 Reply


?     Asked on 1/4/2019by Robert

I need to replace the motor for a Pentair whisperflow 1.5 HP wf-26 pump. Is this the correct replacement or is there a better option?
 Reply

A  Answered on 1/4/2019 by InyoPools Product Specialist Patrick P.

Hi Robert, this is the correct replacement motor for your Pentair Whisperflo WF-26 pump and would be the motor we suggest.
 Reply


?     Asked on 2/1/2019by Kelly

will this replace Century A.O. Smith B129?
 Reply

A  Answered on 2/1/2019 by InyoPools Product Specialist Lennox H.

Hi, Kelly. Unfortunately, this PL2854 will not replace the B129 motor. You can use the B129 or the ST1102 as a replacement. 
 Reply


?     Asked on 2/6/2019by Arthur Espinoza

Is it certain that this will fit a Jandy stealth? I just attached a couple photos thanks so much for your help

 Reply

A  Answered on 2/7/2019 by InyoPools Product Specialist Michelle B.

Hello, That will be the incorrect motor. This will be the correct motor you will need for your pump.http://www.inyopools.com/Products/00200017039438.htm
 Reply


?     Asked on 2/19/2019by Mike

will your part# PL2854 replace the motor in the attachment? Thank You
 Reply

A  Answered on 2/20/2019 by InyoPools Product Specialist Lennox H.

Hi, Mike. Yes, you can use the PL2854 to replace your existing motor.
 Reply


?     Asked on 2/19/2019by Mike

will your part# PL2854 replace the motor in the attachment? Thank You

 Reply

A  Answered on 2/20/2019 by InyoPools Product Specialist Lennox H.

Hi, Mike. Yes, you can use the PL2854 to replace your existing motor. 
 Reply


?     Asked on 3/5/2019by Mike

Residential Pool. I don't know if I should wire for 230 or 115 and where I should hook up the existing wires (two blue and one green). I know the green should go to the ground but not sure where the two blue should go.
 Reply

A  Answered on 3/5/2019 by InyoPools Product Specialist Lennox H.

Hi, Mike. To wire this motor correctly, you will need to determine which voltage you have. You can use the timer model or the breaker type. Once you've determine the voltage, use the wiring diagram which is located on the motor. 
 Reply


?     Asked on 3/10/2019by JOHN

WHAT IS THE DIFFERENCE BETWEEN A PENTAIR WHISPER FLO MOTOR MODEL WF-26 AND WFE-26
 Reply

A  Answered on 3/11/2019 by InyoPools Product Specialist Michelle B.

Hello, They are the same pump, one is energy efficient.
 Reply


?     Asked on 3/17/2019by Tom

I have a Century CAT - B2982, PN 196443, FR 56Y, SF 1.65. Is the PL2854 a compatible replacement?
 Reply

A  Answered on 3/17/2019 by InyoPools Product Specialist Lennox H.

Hi, Tom. This PL2854 Single Speed motor can be used as a replacement to the Century B2982 Dual Speed motor. 
 Reply


?     Asked on 4/2/2019by Phillip Bode

is the PL2854 an acceptable replacement for the Century B2852
 Reply

A  Answered on 4/3/2019 by InyoPools Product Specialist Patrick P.

Hi Phililp, If you have a B2852 Motor then you would want to use the 3/4 HP Century B2852 Motor as a replacement. If you wanted to increase the HP on your pump from 3/4 HP to 1.5 HP then you could use this motor but you will need to also replace your impeller from a 3/4 HP impeller to a 1.5 HP impeller.
 Reply


?     Asked on 4/3/2019by Rick

Is this a drop-in replacement motor for Zodiac FHPM 1.5?

 Reply

A  Answered on 4/3/2019 by InyoPools Product Specialist Lennox H.

Hi, Rick. Yes, this motor will be a drop in replacement. 
 Reply


?     Asked on 4/3/2019by Rick

Is the 1.5 HP Square Flange 56Y Up Rate Motor - PL2854 a drop-in replacement motor for Zodiac FHPM 1.5?
 Reply

A  Answered on 4/3/2019 by InyoPools Product Specialist Lennox H.

Hi, Rick. Yes, this motor can be used as a drop in replacement.
 Reply

  • Commented on 4/3/2019 by Product Owner

    What is the tune-up kit for the Jandy Flopro pump?
     Reply


?     Asked on 4/3/2019by Rick

Are there bearings that can be replaced on a Zodiac FHPM 1.5? Is it possible that just the bearings are causing the increasing squealing sound? Thanks
 Reply

A  Answered on 4/3/2019 by InyoPools Product Specialist Lennox H.

Hi, Rick. Yes, bad motor bearings are what is causing the loud squealing sound emitting from the motor. They can be replaced with the proper tools and correct bearing size.
 Reply


?     Asked on 4/4/2019by Rick

What is the tune up kit for the Jandy Flopro? I'll need it for a new motor install. Thanks
 Reply

A  Answered on 4/4/2019 by InyoPools Product Specialist Lennox H.

Hi, Rick. There is not a tune up kit available for the Jandy FloPro pump. The seals will have to be purchased separately which are listed on the Jandy FloPro FHPM Series Pump (2008-Preset) Parts Diagram page.  
 Reply


?     Asked on 4/10/2019by Inyo Visitor

Will this work to replace the pool pump shown in the photo?

 Reply

A  Answered on 4/10/2019 by InyoPools Product Specialist Michelle B.

Hello, This will not be compatible to what you currently have. This will be the correct replacement motor you will need.http://www.inyopools.com/Products/00200017001213.htm
 Reply


?     Asked on 4/13/2019by Blake

Will this motor work with this pump?

 Reply

A  Answered on 4/13/2019 by InyoPools Product Specialist Patrick P.

Hi Blake, When replacing your motor you need to match the True HP (THP) so you will actually need the PL2859 2 HP Motor which has the same True HP of your motor shown in the photo 2 HP x 1.1 Service Factor = 2.2 THP. When replacing your motor you will also need the Pentair Whisperflo Tune Up Kit. We also have a Video on How to Replace a Pool Pump Motor which you may find helpful with you tackle this project.
 Reply


?     Asked on 4/23/2019by Jimmy

I have the jandy FHPM 2.0, will this motor work?
 Reply

A  Answered on 4/23/2019 by InyoPools Product Specialist Michelle B.

Hello,Can you please send a picture of the motor label?
 Reply


?     Asked on 4/23/2019by BOB

THIS LOOKS LIKE MY PUMP MOTOR. . 2007 STA RITE MAX E PRO MODEL P6RA6F 206L 1.5 HP SQUARE FLANGE WILL THIS WORK OR IS THE AO SMITH 1.5 48Y UPRATE USQ1152 BETTER?
 Reply

A  Answered on 4/24/2019 by InyoPools Product Specialist Lennox H.

Hi, Bob. This PL2854 will work as a replacement for your model pump.
 Reply


?     Asked on 4/26/2019by BA Carter

I am looking to replace my pool pump motor. I have attached a photo of the existing motor and the pump it is attached to. Can you please confirm this motor will work and also which gasket kit I need to fit the pump? I look forward to your response and thank you for your help!

 Reply

A  Answered on 4/26/2019 by InyoPools Product Specialist Lennox H.

Hi, BA Carter. This PL2854 motor can be used as a replacement. You will also need the TriStar Pump Tune Up Kit - GOKIT81
 Reply


?     Asked on 4/26/2019by Robert Calistri

Is this a drop in replacement for this motor? Are there any other parts i'll need to replace it?

 Reply

A  Answered on 4/26/2019 by InyoPools Product Specialist Lennox H.

Hi, Robert. This PL2854 motor will not be a compatible replacement. You can use one of the following motors; SPX3215Z2BER, or B2983 along with the TriStar Pump Tune Up Kit - GOKIT81.
 Reply


?     Asked on 4/27/2019by Josh

I have a white river motor looking to changed model is cs4m25714l not sure what motor frame is 48 thanks

 Reply

A  Answered on 4/28/2019 by InyoPools Product Specialist Patrick P.

Hi Josh, You would require the BN35V1 1.5 HP Replacement Motor, as well as this Replacement Pool Shaft, as well as this Replacement Pool Shaft Seal It would actually be less expensive to purchase the complete PL1502 PureLine Pure Pro XL which is a drop-in replacement for your White River Pump.
 Reply

  • Commented on 4/28/2019 by Product Owner

    It bolts up to a square flange u sure it's the right motor

     Reply


?     Asked on 5/1/2019by Sara Titchener

I have a Pentair 1/2HP ..60Hz 1Ph kW..pump model WFE-2/ 011511. Bought new less than 2 years ago..now making a very loud high pitch sound. Have been told by my pool guy that it needs to be replaced. Seriously?? not even 2 years old? My first pump was a Centurion that lived for 22 years. What do you suggest as a replacement..that will last more than 2 years?
 Reply

A  Answered on 5/2/2019 by InyoPools Product Specialist Patrick P.

Hi Sara, You will need the Century B2845 1/2 HP Replacement Motor Century makes a good motor and should be happy with that. You will also need a Whisperflo Tune Up Kit when replacing your motor.
 Reply


?     Asked on 5/2/2019by Sally

Would this motor work as a replacement for a Pentair Whisperflo WF-24? Thanks.

 Reply

A  Answered on 5/2/2019 by InyoPools Product Specialist Patrick P.

Hi Sally, the proper replacement motor for your Pentair Whisperflo WF-24 would be the PL2853 1 HP Replacement Motor and not this PL2854 1.5 HP Motor. We would also suggest a Whisperflo Tune Up Kit when you replace your motor.
 Reply


?     Asked on 5/3/2019by Dan

Is this the proper replacement part. What else do i need?

 Reply

A  Answered on 5/4/2019 by InyoPools Product Specialist Lennox H.

Hi, Dan. Yes, this PL2854 motor is the correct replacement. You will also need the WhisperFlo Pump Tune Up Kit -  GOKIT32 or GOKIT32SALT
 Reply


?     Asked on 5/8/2019by Etavis Dawson

i have a max flo xl pump. it has a 8ft lift model number c48d43a04. rotation cwle class b code j ph1. will this pump match up with the one i have?
 Reply

A  Answered on 5/8/2019 by InyoPools Product Specialist Hector F.

The correct replacement motor is the model USQ1152
 Reply


?     Asked on 5/9/2019by Julie

I am replacing a Zodiac-Jandy Stealth SHPM1.5. Will this motor work? Also what other parts would I need? Zodiac recommends replacing the Mechanical Shaft Seal and backplate o rings. Thank you!

 Reply

A  Answered on 5/9/2019 by InyoPools Product Specialist Hector F.

You can use either single speed motor models PL2854, B848 or B2854. In order to confirm the correct main shaft seal, you will need the serial number of the front pump housing. Please click here to view those seals at key 5 and the serial number ranges to confirm the one you need. 
 Reply


?     Asked on 5/9/2019by Jeff

I need to replace the motor on a Jandy PHPM1.5 pump. What replacement motor do you recommend and what is the correct seal and ring set? thanks.
 Reply

A  Answered on 5/13/2019 by InyoPools Product Specialist Michelle B.

Can you please take a picture of the motor label? Also what is the serial number of the pump?
 Reply


?     Asked on 5/9/2019by Peter

Will this pump work for me

 Reply

A  Answered on 5/9/2019 by InyoPools Product Specialist Hector F.

Your replacement motor is actually the model UCT1152.
 Reply


?     Asked on 5/13/2019by Brett Frisse

What is the correct motor replacement for the following? Pentair Dual Speed 1.5hp motor? See the attached picture?

 Reply

A  Answered on 5/13/2019 by InyoPools Product Specialist Lennox H.

Hi, Brett. The B2982 replacement motor is the correct replacement that will match the total hp of your original motor. You will also need to get the SuperFlo Tune Up Kit - GOKIT78.
 Reply


?     Asked on 5/17/2019by Bill W

Is this the right replacement motor for my 1.5 hp Pentair Poop Pump?

 Reply

A  Answered on 5/17/2019 by InyoPools Product Specialist Patrick P.

Hi Bill, Yes this is the proper replacement for your motor listed in your photos.
 Reply


?     Asked on 5/21/2019by Inyo Visitor

Will this motor work to replace this motor?

 Reply

A  Answered on 5/22/2019 by InyoPools Product Specialist Michelle B.

Hello, This will be the seal kit you will need., http://www.inyopools.com/Products/00500000040110.htmThis will be the replacement motor you will need. http://www.inyopools.com/Products/00200017039448.htm
 Reply


?     Asked on 5/24/2019by Ruben

Would this work for a replacement of a Century B129 1.5HP?
 Reply

A  Answered on 5/24/2019 by InyoPools Product Specialist Lennox H.

Hi, Ruben. This PL2854 motor cannot be used as a replacement for the B129 motor.
 Reply


?     Asked on 5/25/2019by Inyo Visitor

how to Remove back cover from PL2859 motor
 Reply

A  Answered on 5/25/2019 by InyoPools Product Specialist Lennox H.

Hi. There is (2) Screw that holds the electrical cover plate to the motor body.. 
 Reply


?     Asked on 5/31/2019by Kodi

I'm missing the part number but will this work to replace my Hayward shown in the photos? I see a 1.5HP; 1.60 SF 2.40 THP on top of the motor.

 Reply

A  Answered on 6/11/2019 by InyoPools Product Specialist Matt S.

Your pump model is a Hayward TriStar 1-1/2 HP, Energy Efficient, Full Rated, so the B854 is not going to work for you. The p-to-date motor replacement suited for that pump is the SQ1202.
 Reply


?     Asked on 6/5/2019by Rob

Hello. Is this the correct motor to replace a Centurion 193986XCN on a Jandy FLOPRO FHPM1.5 pump? Also, what shaft seal and housing seal kits would I need to replace the pump? Thank you!

 Reply

A  Answered on 6/5/2019 by InyoPools Product Specialist Lennox H.

Hi, Rob. You will need this PL2854 along with the  Pump Shaft Seal 5/8" OEM - R0479400, BackPlate O-ring - R0480300, and Diffuser & Impeller Hardware - R0480400
 Reply


?     Asked on 6/5/2019by Cliff

I have an AO Smith B2854 motor, it appears the PL2854 would also be compatible and it is cheaper. Any difference when comparing the motors such as features and quality?
 Reply

A  Answered on 6/6/2019 by InyoPools Product Specialist Patrick P.

Hi Cliff, We have found the AO Smith/Century and PureLine motors both to be great motors and there are not major differences when comparing the motors such as features and quality.
 Reply


?     Asked on 6/5/2019by Lonnie Arnold

Is this right replacement motor for clean choice model B2983
 Reply

A  Answered on 6/5/2019 by InyoPools Product Specialist Patrick P.

Hi Lonnie, The direct replacement for your B2983 would be this Century B2983 1.5 HP Full Rate Dual Speed Motor if you wanted to go to single speed motor then you could go with this PL2859 2 HP Up Rate Replacement Motor Please note that if you live in California then you will have to stay with a Dual Speed Motor.
 Reply


?     Asked on 6/7/2019by larry

how fast is your shipping
 Reply

A  Answered on 6/7/2019 by InyoPools Product Specialist Patrick P.

Hi Larry, You can expect to receive the motor in 3-5 business days.
 Reply


?     Asked on 6/8/2019by Ronald Simmons

We have a Century switceless B849 motor, FR: Y56Y, 1.5 HP, square flange. Is this the correct replacement motor?

 Reply

A  Answered on 6/9/2019 by InyoPools Product Specialist Michelle B.

Hello, This will be the proper motor you will need.http://www.inyopools.com/Products/07501352022116.htm?Keywords=b849
 Reply


?     Asked on 6/9/2019by Rav

I have a Centurion Switchless motor 230/115V HP.1.5 SF 1.5Y56Y RBM3450 . Will the PL2854 be a good option for replacement?
 Reply

A  Answered on 6/10/2019 by InyoPools Product Specialist Patrick P.

Hi Rav, If you have a 1.5 SF then you will actually need the PL2859 2 HP Up Rate Replacement Motor We do always suggest a Seal Kit when replacing a motor. To determine the proper seal kit we will need to know your pump make and model information, common pump names would be Pentair Whisperflo, Pentair Challenger, Jandy Stealth, Sta-Rite Duraglas, etc.. To supply this information click the reply link below, also if you could send a few photos those are always helpful as well. If you send photos then take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
 Reply


?     Asked on 6/10/2019by Dave

Pentair 1.5hp superflo. Is this the right replacement motor?

 Reply

A  Answered on 6/10/2019 by InyoPools Product Specialist Lennox H.

Hi, Dave. Yes, this PL2854 motor is the correct replacement. You will also need to get the SuperFlo Tune Up Kit - GOKIT78
 Reply


?     Asked on 6/11/2019by Inyo Visitor

Will this motor be a direct replacement to A.O. Smith C48L2PA105C5

 Reply

A  Answered on 6/11/2019 by InyoPools Product Specialist Matt S.

For the most part, the PL2854 is a straightforward replacement for the C48L2PA105C5 (USQ1152). The PL2854 is a 56Y motor, which means the barrel of the motor is wider, so you may need to remove the small rubber pad or bumper that sits under your motor.
 Reply


?     Asked on 6/12/2019by Inyo Visitor

I have a jandy stealth pump model SHPF1.5 i need to replace the motor which model would i be looking for? thankyou
 Reply

A  Answered on 6/12/2019 by InyoPools Product Specialist Lennox H.

Hi. The B2858 (Standard) or the B2842 (Energy Efficient) motors are the replacement options for your model pump.
 Reply


?     Asked on 6/15/2019by Mk stirn

Will this replace a b2854 1.5 hp century pump?
 Reply

A  Answered on 6/26/2019 by InyoPools Product Specialist Hector F.

Yes, this a replacement for the the model B2854 motor. 
 Reply


?     Asked on 6/16/2019by Randall Luke

Will this motor work as a replacement for a sta-rite P6RA6F-206L pump ?
 Reply

A  Answered on 6/16/2019 by InyoPools Product Specialist Lennox H.

Hi, Randall. Yes, this motor can be used as a replacement. You will also need the Max-E-Pro Tune Up Kit - GOKIT79.
 Reply


?     Asked on 6/17/2019by Robert Lowrey

will this motor work as a direct replacement for the original motor in a whisperflo WF-26, P/N 011773, motor #196239, 1.5 hp?
 Reply

A  Answered on 6/19/2019 by InyoPools Product Specialist Matt S.

Yes, the PL2854 is a direct replacement for the WhisperFlo WF-26's 1.5HP motor.
 Reply


?     Asked on 6/17/2019by Jeffrey Thomas

Please can you confirm if this is a direct replacement for this motor?

 Reply

A  Answered on 6/18/2019 by InyoPools Product Specialist Matt S.

Hello, the replacement motor for your 0-193989-05 is the 1 HP Square Flange 56Y Dual Speed Full Rate Motor - B2982.
 Reply


?     Asked on 6/21/2019by Doug Sullivan

Will this motor replace my Century O-193986-24 (MOD# 193986XCN)?

 Reply

A  Answered on 6/21/2019 by InyoPools Product Specialist Lennox H.

Hi, Doug. Yes, this PL2854 motor will work as a replacement. 
 Reply

  • Commented on 6/21/2019 by Product Owner

    AWESOME!!!!
     Reply


?     Asked on 6/21/2019by Inyo Visitor

Will this pump replace my A/O Smith 1-177216-24
 Reply

A  Answered on 6/22/2019 by InyoPools Product Specialist Patrick P.

Yes this is the correct replacement motor for the 1-177216-24. We do always suggest a Seal Kit when replacing a motor. To determine the proper seal kit we will need to know your pump make and model information, common pump names would be Hayward Super Pump, Hayward Super II, Hayward Max Flo, Pentair Whisperflo, Pentair Challenger, Jandy Stealth, Jacuzzi Magnum, Sta-Rite Duraglas, etc.. To supply this information click the reply link below, also if you could send a few photos those are always helpful as well. If you send photos then take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
 Reply


?     Asked on 6/21/2019by Bill Hubbs

will this motor work as a replacement for this

 Reply

A  Answered on 6/22/2019 by InyoPools Product Specialist Patrick P.

Hi Bill, Yes this is the correct replacement motor the motor included in your photo. We do always suggest a Seal Kit when replacing a motor. To determine the proper seal kit we will need to know your pump make and model information, common pump names would be Hayward Super Pump, Hayward Super II, Hayward Max Flo, Pentair Whisperflo, Pentair Challenger, Jandy Stealth, Jacuzzi Magnum, Sta-Rite Duraglas, etc.. To supply this information click the reply link below, also if you could send a few photos those are always helpful as well. If you send photos then take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
 Reply


?     Asked on 6/23/2019by Jorge

Will it for this?

 Reply

A  Answered on 6/23/2019 by InyoPools Product Specialist Lennox H.

Hi, Jorge. Yes, this PL2854 along with the Challenger Pump Tune Up Kit -  GOKIT5 or GOKIT5SALT.
 Reply


?     Asked on 6/24/2019by Replacement for Century Pool Motor B129

Would this motor repace the Century Pool Motor B129?
 Reply

A  Answered on 6/24/2019 by InyoPools Product Specialist Matt S.

It would not. The PL2854 and the B129 use different mounting flange types. The closest Pureline Motor option is the PL1152
 Reply


?     Asked on 6/24/2019by Vickie

I have a StaRite C48K2PA105 motor. Can I replace it with this one. I know what I have is 1 hp but wondering if a 1.5 hp might be better. I have a 35000 gal pool
 Reply

A  Answered on 6/24/2019 by InyoPools Product Specialist Matt S.

Yes, you could replace the USQ1102 with the B854, but you would need to change the impeller and possibly the diffuser to see any actual change in water flow. But if your system was running fine with the 1HP, I would be hesitant in trying to switch it up.
 Reply


?     Asked on 6/25/2019by Inyo Visitor

Will this work for this?

 Reply

A  Answered on 6/25/2019 by InyoPools Product Specialist Matt S.

The PL2854 is not a compatible motor for your UST1152; you would need to replace it with another UST1152, or a 1.5 HP Round Flange 56J Up Rate Motor - B229SE as a super efficient single speed option.
 Reply


?     Asked on 6/27/2019by Frank Nelson

will this be a direct fit replacement for my Pentair whisperflow? Part # 0-177451-03 frame y56y type CX formKJM single phase 1.5 HP 230V
 Reply

A  Answered on 6/27/2019 by InyoPools Product Specialist Matt S.

The uprated PL2854 is not compatible with your 0-177451-03, 1.5 HP Square Flange 56Y Full Rate EE Motor. The 854 is a less powerful motor and will not be able to turn your pump's impeller.
 Reply


?     Asked on 6/28/2019by Scott Gurley

Pump stopped working - motor getting power and is hot to touch - I am thinking just replacing motor will fix the problem - thoughts? Anyway to troubleshoot to make certain pump replacement will work? See pictures of current pump and suggest replacement please. Thanks can call if needed.

 Reply

A  Answered on 6/28/2019 by InyoPools Product Specialist Lennox H.

Hi, Scott. You can use the A.O. Smith Motor Troubleshooting Guide to diagnose the issue with your motor. If you end up needing to replace it, this PL2854 along with the Challenger Pump Tune Up Kit - GOKIT5 or GOKIT5SALT are the primary parts you'll need if all the other components are okay. 
 Reply


?     Asked on 6/28/2019by Jorge Vasquez

So I have this pentair pump. And I just order this pump from inyopools. Im a bit confused after watching the video from converting 230v to 115v Do I have to do any of that? The pentair is the pump I’m removing and the pure line is the new one I’m installing

 Reply

A  Answered on 6/29/2019 by InyoPools Product Specialist Lennox H.

Hi, Jorge. To determine the proper wiring, you will have to confirm your electrical voltage, whether it's 115 or 230 volts. Then wire the motor as specified.
 Reply

  • Commented on 6/29/2019 by Product Owner

    How can I determine the voltage ?
     Reply

    • Commented on 6/30/2019 by InyoPools Product Specialist Patrick P.

      You can put a voltmeter on the two incoming wires to determine the voltage. Or if the wires are still hooked up to the Pentair motor then you could take a photo and post back to this comment by clicking reply and we should be able to tell to which voltage your old motor was wired.
       Reply


?     Asked on 6/29/2019by Inyo Visitor

Will this one fit a “Pentair High Performance Pump”??
 Reply

A  Answered on 6/30/2019 by InyoPools Product Specialist Patrick P.

Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
 Reply


?     Asked on 6/30/2019by Juan

My motor shuts off after about 10 seconds it is also hot to the touch and it smells burnt ! I have a Jandy FloPro Series 1Hp . Is this motor compatible with the Jandy ?
 Reply

A  Answered on 9/18/2019 by InyoPools Product Specialist Hector F.

So in order to confirm if this motor is compatible, we will need your current motor model, part or catalog number to confirm for you. If you cannot locate that information please email us a photo of the motor label to upload@inyopools.com so we can review and further advise.
 Reply


?     Asked on 6/30/2019by Juan

My Pump motor will only stay on for about 10 seconds . I have a Jandy FloPro 1HP Model Number #FHPM1.0 Serial Number C13JF1596.

 Reply

A  Answered on 7/1/2019 by InyoPools Product Specialist Matt S.

The replacement for your 0-193985-04 motor would be the B853 or the PL2853. The correct replacement shaft seal for your Jandy FHPM1.0 is the R0479400 - Pump Shaft Seal 5/8" OEM.
 Reply


?     Asked on 7/5/2019by Inyo Visitor

Is this the correct replacement for my pump? Sorry, the label is pretty faded.

 Reply

A  Answered on 7/5/2019 by InyoPools Product Specialist Lennox H.

Hi. It is not, the B2848 motor is the correct replacement. You will also need the WhisperFlo Pump Tune Up Kit -  GOKIT32 or GOKIT32SALT.  
 Reply


?     Asked on 7/7/2019by Peter Ho

Will this motor replace Starite P6RA6F-206L motor
 Reply

A  Answered on 7/8/2019 by InyoPools Product Specialist Matt S.

Yes, the PL2854 is a compatible replacement for you Sta-Rite Max-E-Pro 1.5 HP motor.
 Reply


?     Asked on 7/8/2019by James Willett

i need a replacement motor for a marathon 1 1/2 hp model #5kc39un6086x code L CAT #C1246 FR 56Z ALONG WITH A SEAL KIT
 Reply

A  Answered on 7/8/2019 by InyoPools Product Specialist Joe S.

Hello James, yes based on C1246 the PL2854 would be a replacement motor for that unit. Finding the Tune Up Kit for Your Pool Pump
 Reply


?     Asked on 7/10/2019by Jason

What replacement motor would work for this. My current motor runs in low and faults in high.

 Reply

A  Answered on 7/10/2019 by InyoPools Product Specialist Joe S.

The motor you will need is A.O. Smith 1 HP Square Flange 56Y Dual Speed Full Rate Motor - B2982.
 Reply


?     Asked on 7/12/2019by Robin

I have a jandy stealth 1.5 hp pump. What would be a good replacement outside of jandy for this pump. Thank you

 Reply

A  Answered on 7/12/2019 by InyoPools Product Specialist Matt S.

Hello - your JHP1.5 Jandy Stealth uses a fullrated motor, this means you would need the B128 - 1 HP Round Flange 56J Full Rate EE. The JHP and JHPU models uses the GOKIT77 gasket kit.
 Reply


?     Asked on 7/13/2019by Juan Deglado

Hi, I have a Jandy FloPro Series Pumps two speed 1.5 - 1.6 for 230 V, I want to know which is the best match for it.

 Reply

A  Answered on 7/14/2019 by InyoPools Product Specialist Lennox H.

Hi, Juan. The B2982 which also has a THP of 1.65 is the correct dual speed motor. You can also find the replacement seals listed on the Jandy FloPro FHPM Series Pump (2008-Present) Parts Diagram
 Reply


?     Asked on 7/15/2019by Michael Ayers

Looking to replace our pool pump motor, We currently have a Cetury SP3215Z1BE 1.5 HP 60 Hz, can your recommet the replacement
 Reply

A  Answered on 7/15/2019 by InyoPools Product Specialist Hector F.

You can use the replacement Pureline model PL2859 or the original model 5112-256.
 Reply


?     Asked on 7/18/2019by Pentair Pump Motor

What pump motor do I need to replace Pentair motor HP 1.5 motor # 168453 pump model CHII N1 1 5A / 346206

 Reply

A  Answered on 7/18/2019 by InyoPools Product Specialist Hector F.

You can use this motor as your replacement single speed motor or the B2854
 Reply


?     Asked on 7/19/2019by Todd

Need replacement motor

 Reply

A  Answered on 7/19/2019 by InyoPools Product Specialist Lennox H.

Hi, Todd. The correct replacement motor is the B849 - A.O. Smith 1.5 HP Square Flange 56Y Full Rate Motor. 
 Reply


?     Asked on 7/23/2019by Courtney Vogel

I have a PENTAIR CFII-N1-1.5F will this motor work as a replacement? And what gasket kit will i need?

 Reply

A  Answered on 7/23/2019 by InyoPools Product Specialist Lennox H.

Hi, Courtney. The correct replacement motor is the A.O. Smith 1.5 HP Square Flange 56Y Full Rate EE Motor - B2842. The replacement gaskets are all listed on the Pentair / Pac Fab Challenger CH / CF Series Parts Diagram page.
 Reply


?     Asked on 7/24/2019by Gregory Kemp

Will this motor replace my current motor?

 Reply

A  Answered on 7/24/2019 by InyoPools Product Specialist Lennox H.

Hi, Gregory. Yes, this PL2854 motor is the correct replacement. 
 Reply


?     Asked on 7/26/2019by Inyo Visitor

Looking for a replacement motor for Pentair Superflo 340043 pump 1.5 hp, dual speed.
 Reply

A  Answered on 7/26/2019 by InyoPools Product Specialist Lennox H.

Hi. The B2982 Dual Speed Motor is the correct replacement. You will also need to get the SuperFlo Tune Up Kit - GOKIT78.
 Reply


?     Asked on 7/28/2019by Mike Z

Hi - I have a Pinnacle pump with model # O-177474-01 that is pretty noisy. How loud is a new pump and what one would I need with a gasket kit? Thanks.

 Reply

A  Answered on 7/28/2019 by InyoPools Product Specialist Lennox H.

Hi, Mike Z. The PL2853 motor is the correct replacement and is very quiet just like a brand new motor. You will also need the Pentair Pinnacle Pump Tune Up Kit - GOKIT24
 Reply


?     Asked on 8/1/2019by Nick

Is this changeable with a sta-rite 1.5hp max e-pro ? How fast can you deliver to Florida ? Thanks
 Reply

A  Answered on 8/1/2019 by InyoPools Product Specialist Lennox H.

Hi, Nick. Yes, this motor can be used with selected models of the Max-E-Pro Pump. You can receive it within 1-3 business days. 
 Reply


?     Asked on 8/5/2019by FB

Does this pump fit, Pentair Whisper Flow WF 26 1 1/2 HP

 Reply

A  Answered on 8/6/2019 by InyoPools Product Specialist Michelle B.

Hello, Yes, that will be the correct motor replacement for the wf-26 pump.
 Reply


?     Asked on 8/10/2019by TK

Will this replace Pentair CFII N1 1.5A/343234?

 Reply

A  Answered on 8/11/2019 by InyoPools Product Specialist Lennox H.

Hi, TK. Yes, this PL2854 motor will work as a replacement. 
 Reply


?     Asked on 8/13/2019by Inyo Visitor

Will this work on this model?

 Reply

A  Answered on 8/13/2019 by InyoPools Product Specialist Lennox H.

Hi. This PL2854 will work as a replacement. You will also need the SuperMax Tune Up Kit - GOKIT78
 Reply


?     Asked on 8/16/2019by Roger Barker

Hi. Can you guide me in the right direction for a replacement and any necessary items to complete the install.

 Reply

A  Answered on 8/18/2019 by InyoPools Product Specialist Lennox H.

Hi, Roger. This PL2854 motor can be used as a replacement. You will also need to replace the seals within the pump. If you do not have the pump model, check out our Replacing Parts For A Pump You Don’t Have A Model Number For Blog.
 Reply


?     Asked on 8/19/2019by Josh

Will this replace the century SP3215Z1BE?

 Reply

A  Answered on 8/22/2019 by InyoPools Product Specialist Joe S.

Based on the photo provided you will need to order MANUFACTURER CODE SPX3215Z1BER PART # 5112-256 
 Reply


?     Asked on 8/20/2019by Matt

Hi, is this the correct replacement motor?

 Reply

A  Answered on 8/21/2019 by InyoPools Product Specialist Michelle B.

Hello, Yes, that will be the correct motor.
 Reply


?     Asked on 8/21/2019by Mark

Can you please tell me the replacement motor for the one in the photo as well as the necessary gasket kit? WS-26, HP 1.5, SF 1.1, FR Y56Y.

 Reply

A  Answered on 8/21/2019 by InyoPools Product Specialist Lennox H.

Hi, Mark. This is the correct replacement. You will also need the WhisperFlo Pump Tune Up Kit -  GOKIT32 or GOKIT32SALT.
 Reply


?     Asked on 8/21/2019by Mark

Thanks for the information. Will the B2854 also work?
 Reply

A  Answered on 10/2/2019 by InyoPools Product Specialist Hector F.

Yes, the B2854 single speed motor will also be a compatible replacement. 
 Reply


?     Asked on 4/11/2020by Sam

I have a Pentair Superflow Pump 1.5HP 230V model 340039 and the motor appears to have seized. Two sets of questions: What would I need or do you recommend to rebuild this pump with a new motor in exact same function? (Motor, rebuild kits, seals, etc.) Is it possible to update to a variable speed motor with old pump body for my pump? If so, what do I need or do you recommend? (Motor, rebuild kits, seals, etc.) Thanks, Sam
 Reply

A  Answered on 11/17/2020 by InyoPools Product Specialist Megan C.

The Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854 is the single-speed replacement. The Variable Speed (California Title 20 Compliant) is the V-Green 1.65 HP Round Flange 56J Variable Speed Motor - ECM16CU (for 208-230 Volts Only) The Tune-Up Kit Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78 will be used for either motor, add the Pump Shaft Seal Heavy Duty (Saltwater Pools) - PS-3867 with the order of the Gokit78 for salt pools. The 340039 is designed for 230 or 115 Volts, the SuperFlo VS Variable Speed Pump 115/230V - 342001 can be used to replace it.
 Reply


?     Asked on 5/16/2020by steve

what is the shaft size
 Reply

A  Answered on 12/4/2020 by InyoPools Product Specialist Hector F.

Hi Steve, the shaft size of this motor is 1/2 inch. 
 Reply


?     Asked on 6/2/2020by Frank Cheesman

I need a price Quote on a PL2854 motor,I had purchased the same motor less than a year ago and now it must be replaced.
 Reply

A  Answered on 6/2/2020 by InyoPools Product Specialist Patrick P.

Hi Frank, We would suggest this B2854 Motor made by Century as the proper replacement
 Reply


?     Asked on 10/13/2020by Lonnie Houck III

This came up as optional replacement for Centurion 0-F56AA40A01 - 24 1.5 HP Square Flange 56Y Up Rate Motor - PL2854 Is this correct and will assemble directly to current pump. If so what seal kit / shaft seal is needed? Thanks
 Reply

A  Answered on 10/13/2020 by InyoPools Product Specialist Hector F.

Actually, the direct replacement motor will be the model B854 that you can view by clicking here as this motor is no longer available. Also, in order to locate the correct seals, we will need to know the model name or number of the front pump housing wet end that the motor attaches to. 
 Reply

  • Commented on 10/14/2020 by Product Owner

    Im not home. Traveling but pump is screaming wife says so trying to order replacement so I can fix as soon as I get home. Can we tell from these photos what shaft seal and o ring kit are needed? I know they are not much

     Reply