?     Asked on 1/11/2012by Guest

What is Service Factor?
 Reply

A  Answered on 1/11/2012 by InyoPools Product Specialist Patrick P.

Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
 Reply


?     Asked on 1/12/2012by Guest

Why do I need to purchase a new shaft seal?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
 Reply


?     Asked on 1/12/2012by Guest

Why should I purchase a Tune Up Kit?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
 Reply


?     Asked on 1/18/2012by Guest

I'm trying to find a replacement motor for my pool pump but my model number doesn't match what you have listed as the model number. My model number begins with a C48 and yours begins with an SP. Please help.
 Reply

A  Answered on 1/18/2012 by InyoPools Product Specialist Patrick P.

What we have listed on our chart pages is the pump model number. The model number you have will just identify the motor. If you look on the plastic housing on the pump there should be a sticker which will have the pump model number. You can usually find this by the discharge port on the pump. Once you locate it you can choose the correct replacement motor. Be certain to change the shaft seal and gaskets as needed. You can use our >How to guide if you need help. 
 Reply


?     Asked on 8/6/2012by Guest

Does this motor come with a cord? If not, do you supply the correct cord?
 Reply

A  Answered on 8/6/2012 by InyoPools Product Specialist Patrick P.

The Magnatek BN25 does not come with a cord. For a 115 volt application, if you need a twist lock cord, you can find it here: http://www.inyopools.com/Products/07501352011327.htm or a standard 3 prong cord here: http://www.inyopools.com/Products/07501352015032.htm  
 Reply


?     Asked on 2/28/2013by Guest

Is there any difference between the AO Smith BN25 and the BN25V1?
 Reply

A  Answered on 2/28/2013 by InyoPools Product Specialist Patrick P.

No. The AO Smith BN25 and the BN25V1 are the same motor. The BN25V1 is the newer part number for the motor.
 Reply


?     Asked on 12/2/2014by renee

My Emerson motor model number is S55CXPLF-7637. What motor is the correct replacement?
 Reply

A  Answered on 12/2/2014 by InyoPools Product Specialist Robert M.

Hello Renee - The BN25 is the correct replacement motor.
 Reply


?     Asked on 1/6/2015by Inyo Visitor

Who is the manufacturer of the BN25?
 Reply

A  Answered on 1/7/2015 by InyoPools Product Specialist Robert M.

The manufacturer of the motor is Century (formerly A.O. Smith).
 Reply


?     Asked on 4/6/2015by Mary

Is this pump a new or refurbished one?
 Reply

A  Answered on 4/6/2015 by InyoPools Product Specialist Lennox H.

Mary, This is the price for a "NEW" motor.
 Reply


?     Asked on 4/21/2015by Kevin

Is there an on-off switch under the back of the motor?
 Reply

A  Answered on 4/22/2015 by InyoPools Product Specialist Robert M.

Hello Kevin - There is not a switch on the back of the motor. The on/off switch is part number 18374501. This part can be purchased separately.
 Reply


?     Asked on 4/30/2015by earl

Replacement for Sta-rite pool pump motor . model JWPAS5F-2A4U
 Reply

A  Answered on 5/1/2015 by InyoPools Product Specialist Patrick P.

Hi Earl, I am showing that the JWPAS5F-2A4U is a 1-1/2 HP pump and would need our 1-1/2 HP JWPA Replacement Motor. When replacing your motor I would strongly recommend replacing your JWPA Shaft Seal as many times if you use your old shaft seal it will not mate up properly with the new motor and leaking will occur.
 Reply


?     Asked on 5/30/2015by Theresa

Will this replace the sta-rite JWPA5EL-2A1 pump
 Reply

A  Answered on 5/31/2015 by InyoPools Product Specialist Patrick P.

Hi Theresa this would be the correct replacement motor for the sta-rite JWPA5EL-2A1 pump. When replacing this motor you will also need the JWPA Shaft Seal here.
 Reply


?     Asked on 6/2/2015by Inyo Visitor

Is the motor already wired with 3 prong cord with plug
 Reply

A  Answered on 6/2/2015 by InyoPools Product Specialist Patrick P.

No this motor does not come with the 3 prong cord with plug, the majority of customers will remove the cord from their old motor and use on their new motor. We do carry a 3 Prong Pool Motor Cord here.
 Reply


?     Asked on 6/9/2015by John

How in the heck do you separate the impeller from the motor.
 Reply

A  Answered on 6/9/2015 by InyoPools Product Specialist Patrick P.

Our guide with Video on How to Replace a Pool Motor shows the impeller removal in detail.
 Reply


?     Asked on 6/14/2015by Peter

Will this motor match mine which is Power-flo SP1700Z2? My electrical board cracked on my motor,can it be replaced?
 Reply

A  Answered on 6/18/2015 by InyoPools Product Specialist Lennox H.

Peter, This 1 H.P 115V Thru Bolt Motor (BN25) can replace your current motor on the Hayward Power-Flo pump. I would recommend confirming the p/n off of the impeller to make sure you're getting the correct size motor. The electrical switch can be replaced on some motor, if you can reply with your motor info I can see if it's available.
 Reply


?     Asked on 6/15/2015by Darlene

I was wondering if the BN 25 is the correct motor/pump to replace the Sta-Rite JWPA5E7L-2A2 ? Will this motor/pump fit onto the existing base? Also, do you ship to Canada? Thank you for your time. Have a wonderful day!
 Reply

A  Answered on 6/15/2015 by InyoPools Product Specialist Patrick P.

Hi Darlene, yes this would be the correct replacement motor for your 1 HP Sta-Rite JWPA5E7L-2A2. This motor would fit onto your current motor base and we do ship to Canada. When replacing your motor we would suggest the Starite JWPA Shaft Seal. We also have A Guide With Video on How to Replace a Pool Pump Motor which should be helpful if you do this repair yourself.
 Reply


?     Asked on 6/15/2015by Ed

Is this motor a direct replacement for my Hayward Power-flo Matrix pool filter. Here the list of numbers on my unit. SP1510-Z-1-XEFTC Sp1592FTTL
 Reply

A  Answered on 6/15/2015 by InyoPools Product Specialist Patrick P.

Hi Ed, Yes this is the correct replacement motor for the 1 HP Hayward Matrix Pump. When replacing the motor on your motor we would suggest replacing your Hayward Matrix Shaft Seal.
 Reply


?     Asked on 6/15/2015by Charles Shepard

what are the motor windings made of? Is the wire windings aluminum? I have been trying to repair the winds.....and they do not appear to be copper colored, and will not take solder.
 Reply

A  Answered on 6/18/2015 by InyoPools Product Specialist Lennox H.

Charles, Some motor windings are made of aluminum or copper. The ones on your motor may be aluminum if not copper colored.
 Reply


?     Asked on 6/21/2015by Inyo Visitor

Is the the replacement motor for jwpa5e7L-2A2
 Reply

A  Answered on 6/22/2015 by InyoPools Product Specialist Dennis R.

Yes, BN25 is the correct 1 HP replacement motor for your Sta-Rite JWPA series pump.
 Reply


?     Asked on 6/27/2015by Eddie

I have a A O Smith motor as part number 7-177760-23 on label which brings up this BN25 as it's replacement. There is also a sticker on the motor that says it's a 1.5 HP A O Smith SPL. ?? Not sure if this is the correct motor.
 Reply

A  Answered on 6/28/2015 by InyoPools Product Specialist Lennox H.

Hi Eddie, The 1 H.P 115V Thru Bolt Motor (BN25) is the correct replacement for p/n 7-177760-23. The 1.5SPL is a reference to the windings in the motor not the HP.
 Reply


?     Asked on 6/29/2015by john

i have a sta-rite pump model number jwpa5e7L-2a1. is this right replacement and is their anything else i'm going to need
 Reply

A  Answered on 6/29/2015 by InyoPools Product Specialist Dennis R.

Hi John, yes the BN25 is the 1 H.P 115V single speed Thru Bolt Motor option for your Sta-Rite JWPA Series pump. You will need to replace the shaft seal. See key #7 in this Sta-Rite JWPA Series Parts List. You have three options for the shaft seal: OEM, Generic, or Salt Water
 Reply


?     Asked on 7/1/2015by Paul

I have this motor on my pool pump. It is currently humming and kicking the breaker. The shaft spins freely by hand. I am looking for the start capacitor and can not find it. There is no side cover and no capacitor behind the the plastic back cover. Does it have one?
 Reply

A  Answered on 7/2/2015 by InyoPools Product Specialist Lennox H.

Hi Paul, You will have to provide us with the specs off of the capacitor to get the correct replacement.
 Reply


?     Asked on 7/6/2015by Cathy

I need to replace the screw on the top end of the motor the man at the store where I bought my unit said you can get it at an electrical store but I don't have any other info can you help
 Reply

A  Answered on 7/6/2015 by InyoPools Product Specialist Dennis R.

Hi Cathy - Not sure what screw you are looking for that's on the top end of the motor but here's a list of the limited motor parts that we sell: Pump Motor Parts. You may be looking for the Thru Bolts that tie some motors together.
 Reply


?     Asked on 7/9/2015by danny williams

Need to replace a Hayward flo matrix sp1510z1xehc, what would be your replacement number .
 Reply

A  Answered on 7/11/2015 by InyoPools Product Specialist Patrick P.

Hi Danny, this would be the correct replacement motor for your Hayward sp1510z1xehc. When replacing your motor we would also suggest a Hayward Matrix Shaft Seal.
 Reply


?     Asked on 7/30/2015by Kelly C

Hi, Would this motor replace A.O.Smith/Century Pool Jetted Tub Motor 7-177894-24?
 Reply

A  Answered on 7/31/2015 by InyoPools Product Specialist Lennox H.

Hi Kelly, The 1 H.P 115V Thru Bolt Motor (BN25) would be the correct replacement motor for your current motor with part # 7-177894-24.
 Reply


?     Asked on 8/3/2015by john

I have a Jacuzzi cfr50 filter/pump combination. the motor is extremely loud and I am looking to replace it. original part is an ao smith 1 hp part # 7-186533-22. will this motor work as a replacement? Thanks
 Reply

A  Answered on 8/4/2015 by InyoPools Product Specialist Patrick P.

Hi John, We are showing that the BN24 Replacement Motor would be the correct motor for you.
 Reply


?     Asked on 8/13/2015by Linda C

I see that this would replace A.O. Smith/Century Pool Jetted Tub Motor. The part # I have is: Part 7 177893-24. Would this replace it? How long does it take to ship? I'm concerned with installation are there instructions ?
 Reply

A  Answered on 8/13/2015 by InyoPools Product Specialist Andy O.

Linda- It looks like part number 7-177893-24 is replaced by BN24V1 3/4 HP Single Speed Motor. Motors usually take 3 business days for delivery. There are no instructions, but you can watch this video for a general idea.
 Reply


?     Asked on 8/30/2015by lloyd

My motor has seized up. What replacement motor for JWPA5E7L-2A2 pool motor
 Reply

A  Answered on 9/1/2015 by InyoPools Product Specialist Lennox H.

Hi Lloyd, The 1 H.P 115V Thru Bolt Motor (BN25) would be the correct replacement motor for your model pump. The replacement does not come with a power cord so you will have to reuse your current power cord if one is used.
 Reply


?     Asked on 9/20/2015by Inyo Visitor

I have a E91 pump need a motor replacement. Pool is above ground 24 foot round. You can't read what HP on motor. It is a 2 speed. Wondering if this replacement of 1 HP will be enough.
 Reply

A  Answered on 9/25/2015 by InyoPools Product Specialist Lennox H.

Hi, The 1 HP motor would be okay but you would want to make sure that the impeller is not size for a larger HP rating.
 Reply


?     Asked on 10/30/2015by George

My motor seized up today. We had many days of rain and I am sure the old motor just shorted. It is a STA-RITE # s48B74A03 1 HP 3450 RPM 12 AMP and it attaches to a PUMP: JWPAS5F. What is the replacement motor needed?
 Reply

A  Answered on 10/30/2015 by InyoPools Product Specialist Lennox H.

Hi George, The A.O. Smith 1 H.P 115V Thru Bolt Motor (BN25) will be the correct replacement motor to replace model # S48B74A03.
 Reply


?     Asked on 2/19/2016by Chuck

Good evening. We have jet spa tub and our motor stopped working. Not sure if its the sensor or the actual motor itself. IF we need to replace the motor what would replace a MagneTek 7-177760-23 HP I. Volts 115. RPM 3450 AMPS 12.4. This is the motor that is currently on our spa tub now
 Reply

A  Answered on 2/22/2016 by InyoPools Product Specialist Lennox H.

Hi Chuck, The A.O. Smith 1 H.P 115V Thru Bolt Motor (BN25) will be the correct replacement motor base off of the information provided.
 Reply


?     Asked on 4/8/2016by Stephen

Will a BN35V1 motor work on my pool replacing a BN25V1?
 Reply

A  Answered on 4/8/2016 by InyoPools Product Specialist Lennox H.

Hi Stephen, The BN35V1 motor can replace the BN25V1 motor, First you will have to make sure that your filter can handle the additional water flow. Once you confirm that it can then you will also need to change the pump impeller and seals.
 Reply


?     Asked on 4/18/2016by Rich

My pool pump is a A.O. Smith # S48B74A03 and it squeals a lot. I want to replace the pump with a BN25. My question is do I need to purchase other items or is all I need included with the pump purchase?
 Reply

A  Answered on 4/19/2016 by InyoPools Product Specialist Lennox H.

Hi Rich, The BN25 will replace the S48B74A03 motor. You will need to replace the pump shaft seal and pump o-rings however, we will need to know the manufacturer and model of the pump housing.
 Reply


?     Asked on 5/27/2016by Tom

My current pool pump motor is a Sta-Rite model # JWPA5E7L-2A1. (1.0 HP) This has probably been discontinued, so what replacement motor should I buy that will be equivalent to the one I have now?
 Reply

A  Answered on 5/27/2016 by InyoPools Product Specialist Dennis R.

Hi Tom, Your replacement motor for this JWPA Series pump is BN25. Don't forget to replace your shaft seal. - Generic or OEM
 Reply


?     Asked on 6/4/2016by ERIC

I HAVE A SPECK POOL PUMP SK P711 15H MODEL # PE71-IIH I AM LOOKING TO REPLACE THE MOTOR CAN YOU HELP ME WITH REPLACING IT WITH THE MODEL,I CANNOT FIND ANY INFORMATION ON THIS MOTOR
 Reply

A  Answered on 6/11/2016 by InyoPools Product Specialist Lennox H.

Hi Eric, The BN25 motor is the correct motor for the PE71-II pump, you will also need to replace the shaft seal and o-rings which can be found via the Speck Model E-71 Pump Parts page.
 Reply


?     Asked on 6/4/2016by Bill

Can this motor replace the motor on a Hayward power-flow matrix sp1510z1xehc?
 Reply

A  Answered on 6/10/2016 by InyoPools Product Specialist Lennox H.

Hi Bill, The BN25 motor can replace the SP1510Z1XEHC. The BN25 motor does not come with a switch.
 Reply


?     Asked on 6/5/2016by Jim

My current motor is a Waterway ezbn24 1.0 hp model number s55cxrjc-8049 10 amp. Would this be my replacement motor?
 Reply

A  Answered on 6/5/2016 by InyoPools Product Specialist Patrick P.

Hi Jim, Even though the BN24 motor that we carry says 3/4 HP it would be the correct replacement motor for you as Waterway uses a special horse power which is rated differently than most manufacturers. You will need the BN24 Replacement Motor.
 Reply


?     Asked on 6/16/2016by Russ

White and black wire. What lines do I use?
 Reply

A  Answered on 6/18/2016 by InyoPools Product Specialist Lennox H.

Hi Russ, The "black" wire goes to L1, the "white" wire goes to L6 and your ground.
 Reply


?     Asked on 6/26/2016by Dan Monroe

I am looking to replace a JWPA5EL2A2 pool motor for a 24 ft round above ground pool which motor is it on your web page?
 Reply

A  Answered on 7/2/2016 by InyoPools Product Specialist Lennox H.

Hi Dan, This BN25 Thru Bolt motor is the correct replacement motor for the JWPA5EL2A2 pump. I  will also recommend replacing the Shaft Seal OEM (37400-0027S) or Generic (PSR 201) and the Volute O-ring (5000-4053).
 Reply


?     Asked on 6/30/2016by sammy

How can i find the part # off a terminal board and on and off switch 1hp hayward pump sp1510
 Reply

A  Answered on 7/5/2016 by InyoPools Product Specialist Lennox H.

Hi Sammy, If you can send us a photo of the Terminal board we can locate the correct replacement.
 Reply


?     Asked on 7/5/2016by Keith

I need to replace my 12 year old JWPA5EL series 1 HP motor on 27 ft round, and I see the BN25 is the choice. 1) Would there be any gain in upgrading to the 1.5 HP motor w/same impeller? 2) Now, the shaft seal leaks, psi reads 14-15 (9-11 normal and I would clean cartridge @ 12), and water flow is pretty much abysmal. Is this attributable to the motor, impeller, leaking seal, or all? Note, I verified no restrictions to flow in the plumbing.
 Reply

A  Answered on 7/9/2016 by InyoPools Product Specialist Lennox H.

Hi Keith, There are no benefits upgrading to a 1.5 hp motor if you keep the same impeller. A leaking shaft seal does not lead to high filter pressure. You will have to replace the motor BN25, Shaft Seal and Volute O-ring along with the cartridge.
 Reply


?     Asked on 7/14/2016by George

looking for a motor for my Sta-Rite JWPA series.I know it's a 1hp/155 volts..thanks
 Reply

A  Answered on 7/14/2016 by InyoPools Product Specialist Alan M.

The correct replacement motor for the Sta-Rite JWPA 1HP is the 1 H.P 115V Thru Bolt Motor - BN25 single speed. If you are looking to replace the 2-speed version you will need the 1 HP 2 Speed 115V Thru-Bolt Motor - BN37V1. We would also recommend that when replacing a motor that you change out the pump seal. The replacement is the Pump Seal 201 - PSR 201.
 Reply


?     Asked on 7/15/2016by bob

looking for Sta-Rite JWPA5E7I-2A1. Pump assembly:
 Reply

A  Answered on 7/15/2016 by InyoPools Product Specialist Alan M.

Here is a link to the Sta-Rite JWPA Series Parts list. The parts list includes the specific pump parts available for the JWPA series.
 Reply


?     Asked on 7/25/2016by Inyo Visitor

I need to know what kind of screw to get to hold the ground lug to my pump body. My pump motor is an EZ48 or EZ BN25, Model S55CXRJD-8050. The ground lug is the copper piece that connects the ground wire coming from my pool to the pump motor housing. I have the ground lug, need to know what type of screw to get. The one I had washed away in heavy rain. I tried chatting with your live chat person but they never replied after the initial contact. My pool is now un-grounded. Need help soon!
 Reply

A  Answered on 7/28/2016 by InyoPools Product Specialist Lennox H.

Hi, I was unable to locate the information that you're requesting.You can stop by a hardware store to see if they have a motor lug available.
 Reply


?     Asked on 8/11/2016by Inyo Visitor

any idea where I can find the centrifugal switch on a JWPA5E7L-2A1...replaced the bearings and broke the round plastic ring. need to replace
 Reply

A  Answered on 8/12/2016 by InyoPools Product Specialist Stacey M.

Hello Cliff, could you please tell me what part you are referring to here and I can better assist you with a replacement part.
 Reply


?     Asked on 8/27/2016by benny

the motor that i have is 40gpm and for some reason the vacume that i have is moving pretty slow compare the way it was a few months ago the psi is above 10 but for some reason its not shooting the water as fast as it useto can it be the motor is going bad do not hear any grinding noise but i sense that something is not right can some one email me back tanks
 Reply

A  Answered on 9/29/2016 by InyoPools Product Specialist Stacey M.

Hello Benny, Check out our "how to" guides on checking your filter because the flow could be compromised, please check your pressure gauge and see if a replacement cartridge would fix the slow moving water flow.
 Reply


?     Asked on 9/11/2016by Inyo Visitor

is this motor the same model as S48C51Z03 sp1580z2
 Reply

A  Answered on 9/12/2016 by InyoPools Product Specialist Scott W.

Yes, that would be a good replacement for your Hayward Power Flo LX.
 Reply


?     Asked on 9/12/2016by Ed Sandner

We just need the end cap of this motor as it has cracked ( the part where the cord comes out of the top. Is this possible to purchase. Nothing wrong with motor.
 Reply

A  Answered on 9/14/2016 by InyoPools Product Specialist Stacey M.

Hello Ed, I think this is the part you are referring to Century N/S Terminal Enclosure (19534902). Please make sure that you have a century motor that will match this, all other parts are here.
 Reply


?     Asked on 9/14/2016by tl

I need to replace this motor so do i need any other parts before i replace it.
 Reply

A  Answered on 9/14/2016 by InyoPools Product Specialist Alan M.

When ever you change out a motor, we would recommend you replace the shaft/pump seal as well. You will need to identify what pump make and model you have in order to locate the correct replacement part. The motor information will not be as beneficial as this replacement motor will fit on a number of different pumps.
 Reply


?     Asked on 9/15/2016by Ronnie Smith

Will this motor replace A Q Smith ...pt #0-177893-24 frame P48Y Ser.# 08210 CH? Should I replace anything on the pump motor? Pump is a Waterway Model SP-10-1N11CB. Part Number 3410413-1502. I had rather replace pump and motor if you can tell me what to use, If you need more information, let me know. Thanks for your help.
 Reply

A  Answered on 9/15/2016 by InyoPools Product Specialist Scott W.

The direct replacement for that pump is part number 5030-101.
 Reply


?     Asked on 9/28/2016by Larry

Hi, I have a pump motor Century Pool A.O. Smith BN25 part number 7-177894-24. The motor has been making a very loud screeching noise so I figure it time to replace it as it is 12 years old. Can you confirm this is the correct replacement. Also what is the power requirement? My current motor has a 230 volt plug and the outlet is 230 volt so I need to make sure this pump works with 230 volt plug. Thanks
 Reply

A  Answered on 9/28/2016 by InyoPools Product Specialist Megan C.

Hello, Larry. Unfortunately, this motor is only 115V. It would be the correct replacement motor using part number 7-177894-24 or 177894 for those whom are 115V only. The BN35V1 is the only dual voltage Thru-Bolt motor I have been able to locate. Using this motor with your existing impeller will be okay, because you have not decreased the size of the motor. Don't forget to replace the shaft seal any time your replace the motor or impeller.
 Reply


?     Asked on 2/16/2017by Paul

Is this the replacement motor for Part 7-176505-22? Do I also need a seal kit?
 Reply

A  Answered on 2/16/2017 by InyoPools Product Specialist Lennox H.

Hi, Paul. The BN25 motor is the correct replacement for p/n 7-176505-22. We highly recommend getting a seal kit if one is available for your pump, however, you  we will need the pump model number to find out if one is available.
 Reply


?     Asked on 4/25/2017by Inyo Visitor

I have a Waterway model SD-15-1N11CC CAT BN25 Part 0-177894-24 what motor and other parts (seals?) would I need to replace an extremely loud motor?
 Reply

A  Answered on 4/25/2017 by InyoPools Product Specialist Scott W.

The replacement motor and shaft seal are part numbers BN25 and 5250-106. Those would be the requirements for your motor install.
 Reply


?     Asked on 5/2/2017by Scott

I have a screaching a.o. smith 1.0hp Model s48b74a03. I would like to replace the bearings What size bearings/part number would i need to complete this job?
 Reply

A  Answered on 5/2/2017 by InyoPools Product Specialist Patrick P.

You would require the Two of the 6203 Pool Motor Bearings.
 Reply


?     Asked on 5/4/2017by eric

Will this motor replace the MagneTek 7-177893-21 ??
 Reply

A  Answered on 5/5/2017 by InyoPools Product Specialist Lennox H.

Hi, Eric. The BN24V1 is the correct replacement for p/n 7-177893-21. You can also use the BN25 motor as a replacement on selected pumps.
 Reply


?     Asked on 5/9/2017by Matthew Campbell

I have this motor on my pool, can I use a bigger hp motor and 230v?
 Reply

A  Answered on 5/9/2017 by InyoPools Product Specialist Hector F.

Yes, you can but usually, that entails using an inground pool pump. Also, you want to be sure that the gallons per minute rating on the filter can handle the flow rate of the stronger pump.
 Reply


?     Asked on 5/9/2017by Matthew Campbell

Hi there, which seal kit would I need to replace this motor? Is there anything else I would need to install? Thanks, Matt
 Reply

A  Answered on 5/10/2017 by InyoPools Product Specialist Lennox H.

Hi, Matthew. The seal kit is specific to the pump, not the motor. Please provide us with the pump model number so that we can recommend the correct kit if one is available or parts.
 Reply


?     Asked on 5/10/2017by Matthew Campbell

Hi there, I'm going to get this motor with a sd-15-1n1cc wet end pump. Which seal kit would I need? Also let me know if i need anything else to install the motor. Thanks, Matt
 Reply

A  Answered on 5/10/2017 by InyoPools Product Specialist Lennox H.

Hi, Matthew. Unfortunately, we do not have a seal kit for that model pump. The replacement pump seal and o-rings are all listed on the Waterway Hi-Flo Above Ground Pump parts page.
 Reply


?     Asked on 5/21/2017by Sharla

I just received this motor, but it doesn't have an on/off switch like my old motor. Is there a way to add a switch?
 Reply

A  Answered on 5/23/2017 by InyoPools Product Specialist Lennox H.

Hi, Sharla. The On/Off Switch - 18374501 is available separately and can be installed on this BN25 motor.
 Reply


?     Asked on 6/6/2017by Mark

I am replacing a MagneTek 1.0 H.P. motor; part# 7-186532-21. I cannot find a reference to this model number anywhere. Will this pump be a suitable replacement? 115 volts, 3450 rpm, frame 48Y, 9.8 amps. Thank you...
 Reply

A  Answered on 6/11/2017 by InyoPools Product Specialist Patrick P.

Hi Mark, yes this would be the proper replacement motor for a 7-186532-21 motor.
 Reply


?     Asked on 6/8/2017by David Rodriguez

Is this the same motor as the AO Smith 7-177760-23?
 Reply

A  Answered on 6/8/2017 by InyoPools Product Specialist Patrick P.

Yes this is the same motor as the AO Smith 7-177760-23
 Reply


?     Asked on 6/13/2017by sophia Gianvecchio

Hi, I have a Jacuzzi tub and its motor seems to be broken. The label has the following: Century Jetted Tub Motor 1795 Pump duty. A.O. SMITH. there is no CAT number. Serial number - BW11-20. Part # 7-187809-21. Which motor I need to buy to replace it? Do I need to buy any other parts beside the motor? Please advise. Thank you, Sophia Gianvecchio
 Reply

A  Answered on 6/16/2017 by InyoPools Product Specialist Lennox H.

Hi, Sophia. The Century BN25 Motor is the correct replacement for Part # 7-187809-21. When replacing the motor it's recommended that you replace the pump seal. To locate the pump seal I will need to know the model of the pump which is different from the motor.
 Reply


?     Asked on 6/19/2017by Ken Purdy

my 1777961 has a pneumatic switch . Is this motor compatible? How can I tell if it is a problem with this switch and not the motor?
 Reply

A  Answered on 6/21/2017 by InyoPools Product Specialist Lennox H.

Hi, Ken. This motor does not come with a pneumatic switch (On/Off) but you may be able to reuse the switch you have. You can try wiring the motor directly bypass the switch to see if the motor runs, if it does not then you know the motor is dead.
 Reply


?     Asked on 6/20/2017by Scott

Is the BN25 motor a replacement for my Emerson 1081 (Model S55NXPSB-7738) ?
 Reply

A  Answered on 6/20/2017 by InyoPools Product Specialist Patrick P.

Hi Scott, Yes this is a suitable replacement motor for the Emerson Model S55NXPSB-7738.
 Reply


?     Asked on 6/21/2017by Tony

What is the replacement bearing number for this motor.
 Reply

A  Answered on 6/21/2017 by InyoPools Product Specialist Patrick P.

Hi Tony, the BN25 motor uses two of the 203 Pool Motor Bearings.
 Reply


?     Asked on 7/7/2017by Ernie

I have a waterway sd-10-1n11cb part # ph1100-3psnp. Will this motor work as a replacement?
 Reply

A  Answered on 7/12/2017 by InyoPools Product Specialist Lennox H.

Hi, Ernie. The Century BN24 Motor is the correct replacement for the Waterway SD-10-1N11CB Pump.
 Reply


?     Asked on 7/17/2017by Samantha

Hi! I have Century Pool Motor A.O. Smith CAT BN25 Part O-177894-04 Type SP Frame P48Y Would this be the correct replacement motor? Thanks!
 Reply

A  Answered on 7/19/2017 by InyoPools Product Specialist Alex V.

Samantha, Yes, this would be the correct replacement for the BN25 motor. Be sure to replace the shaft seal when you replace the motor. 
 Reply


?     Asked on 8/2/2017by Patriot

I have a Manetek Spa Motor item number is 182718. Will this pump work for replacement?
 Reply

A  Answered on 8/2/2017 by InyoPools Product Specialist Lennox H.

Hi, Patriot. Yes, this Century BN25 motor is the correct replacement for part # 182718. 
 Reply


?     Asked on 8/4/2017by Brian

Got a 1HP MagneTek SP1510-E-1-XE, part number 7-184878-21, FR: W48Y, SF 1.00. Need to replace pump for water feature. What pump and seals would I need to replace? Thank you
 Reply

A  Answered on 8/5/2017 by InyoPools Product Specialist Alex V.

Brian, Based on the model number, you can replace it with the BN25. In order to recommend the seals, we would need to know the model number of the pump housing. 
 Reply


?     Asked on 8/7/2017by Dave

I need to replace a Hayward SP1510-Z-1-XEFTC part # 7-193770-22. Is this the right model? Any idea what the FTC means? This will be used on a Sani-tower 275 chlorinator. Thanks.
 Reply

A  Answered on 8/8/2017 by InyoPools Product Specialist Lennox H.

Hi, Dave. I'm not sure what FTC stands for but you can use this BN25 motor or the Hayward SPX1510Z1XE motor. 
 Reply


?     Asked on 8/8/2017by Tom Buckley

Need to replace a Magnetek motor part #: 7-177954-40. Would this be the replacement pump?
 Reply

A  Answered on 8/10/2017 by InyoPools Product Specialist Lennox H.

Hi, Tom. The Century BN24 Motor is the correct replacement for Part # 7-177954-40. 
 Reply


?     Asked on 8/10/2017by john dalessio

I need to replace my above ground pool pump motor. I see that your motor (1 H.P 115V Thru Bolt Motor - BN25) has my model # listed as an alternate motor model #. Mine is a Hayward power flo LX Mod # S48A84A04. I want to verify this is the proper replacement because I see the frame or FR #'s are different. Mine is 56Z and the new one is 48Y. Not sure what the FR #'s mean. Thanks for your help.
 Reply

A  Answered on 9/22/2017 by InyoPools Product Specialist Stacey M.

Hello John, the motor that matches with S48A84A04, is 1 HP Single Speed Motor - BN25V1 this is for frame 48y.
 Reply


?     Asked on 8/31/2017by Inyo Visitor

I have above ground pool. pump out part # A.O Smith 7-186533-22 motor hz60 rpm 3450 volts 115 amps 9.,8
 Reply

A  Answered on 8/31/2017 by InyoPools Product Specialist Hector F.

Your replacement motor is model BN24V1
 Reply


?     Asked on 9/2/2017by Doug

Hello, I have a Pentair pool pump part O-177961-23 1H 115V and was wondering if this pump would work in place of it?
 Reply

A  Answered on 9/4/2017 by InyoPools Product Specialist Lennox H.

Hi, Doug. Yes, this BN25 motor will replace Part # 0-177961-23. 
 Reply


?     Asked on 9/27/2017by Jerry Roberts

Does this have a on/off rocker switch on the end, under the plastic end cover? If no, is one available?
 Reply

A  Answered on 9/27/2017 by InyoPools Product Specialist Lennox H.

Hi, Jerry Roberts. This motor does not come with an On/Off Switch, one can be purchased separately. The Part # is 18374501
 Reply


?     Asked on 10/2/2017by Mary

I have a emerson c55cxfby 2918. What motor do I replace it with?
 Reply

A  Answered on 10/3/2017 by InyoPools Product Specialist Lennox H.

Hi, Mary. The Century BN37V1 motor is the correct replacement motor. This BN25 motor can be used as a single speed replacement option.
 Reply


?     Asked on 10/14/2017by Mark

What is the difference between model #340104 and #340197?
 Reply

A  Answered on 10/16/2017 by InyoPools Product Specialist Lennox H.

Hi, Mark. The Dynamo Pump model #340197 comes with a power cord and model #340104  does not come with a power cord. 
 Reply


?     Asked on 11/5/2017by donald jackson

looking for replacement for a o smith century pool/ jetted tub motor. cat BN 25SS part O-186884-20 frame p48y volts 115 amps 12 Would your BN25 be a match? thanks
 Reply

A  Answered on 11/6/2017 by InyoPools Product Specialist Lennox H.

Hi, Donald. The BN25 is the correct replacement motor for Part # 0-186884-20.
 Reply


?     Asked on 11/7/2017by Jose

Hi-- What is the proper replacement for Magneter Century Pool/ Jetted Tub Motor, Part 7-177760-21? Do you have it in stock? Thank you!
 Reply

A  Answered on 11/7/2017 by InyoPools Product Specialist Lennox H.

Hi, Jose. This BN25 is the correct replacement motor for Part # 7-177760-21. This motor is available to ship immediately. 
 Reply


?     Asked on 11/15/2017by Tim

I have a Pentair PINNACLE PFII-P1-1A 1HP pool pump. What motor do I replace it with?
 Reply

A  Answered on 11/16/2017 by InyoPools Product Specialist Lennox H.

Hi, Tim. Based on your model number, you will need the Century B2853 motor. 
 Reply


?     Asked on 12/4/2017by Vicki

I have a century pool /jetted tub motor BN2355 part 7-186882-20. What would I replace it with
 Reply

A  Answered on 12/5/2017 by InyoPools Product Specialist Kevin G.

To replace this motor, you would want to go with the BN23.
 Reply


?     Asked on 3/4/2018by larry

I have a sta-rite motor #S48B74A03 HP1.5 3450 RPM THat Attaches to a pump model# JWPS5F7L-2a2 what is the repacementment for it
 Reply

A  Answered on 3/5/2018 by InyoPools Product Specialist Lennox H.

Hi, Larry. This BN25 is the correct replacement motor for the Sta-Rite JWPS5F7L-2a2 Pump with motor model # S48B74A03. You will also need to get the Sta-Rite JWPA Seal Kit 1 & 1-1/2 HP - APCK1187.
 Reply


?     Asked on 4/14/2018by Philip Penco

I have a Pentair model number L3-PLUS-160/027016. The motor coil has burnt and I would like to have it rewired is it possible for me to get the specific gauge and length of the wire I should use.
 Reply

A  Answered on 4/20/2018 by InyoPools Product Specialist Megan C.

I was unable to find a cross-reference with the model number  L3-PLUS-160/027016. Please contact Pentair at 1.800.831.7133 or email us using email address upload@inyopools.com with images of the product(s) you are referring to. 
 Reply


?     Asked on 4/17/2018by Brian Woods

Will this motor interchange with my Speck pump model A91-ll the one I have is a 1.5 HP but a 1 HP will do me. The label is off my motor !!
 Reply

A  Answered on 4/20/2018 by InyoPools Product Specialist Lennox H.

Hi, Brian. It cannot, due to the base of the mounting housing. 
 Reply


?     Asked on 5/2/2018by Tom

I have a waterway pump SD1400331 3745 SD101n11cb PN 3410413-2041 and I want a 2 speed to replace it Wh at do I need to replace this
 Reply

A  Answered on 5/5/2018 by InyoPools Product Specialist Lennox H.

Hi, Tom. Youcan replace your existing motor with the BN37V1 2-SPD motor or the Hi-flo Pump, 1 Hp, 2-speed, 120 Volts - 3420410-10
 Reply


?     Asked on 5/19/2018by ken

I have a flopro. emerson motor co. model# S%%NXREK-7955 what model do I replace it with?
 Reply

A  Answered on 5/22/2018 by InyoPools Product Specialist Lennox H.

Hi, Ken. Unfortunately, the partial motor model number is not sufficient to locate the replacement motor. I will need the FloPro pump model # the motor's CAT #.
 Reply


?     Asked on 5/23/2018by rick seguin

Is this the correct replacement for the century jetted pool pump part #186884-20
 Reply

A  Answered on 5/23/2018 by InyoPools Product Specialist Hector F.

This is the correct replacement motor for your model motor. 
 Reply


?     Asked on 5/25/2018by Jackie Knight

I have a splapool motor model 72720 motor model rs4g24213L what do i pelace with HP 1 amps 9.0 rpm 3450
 Reply

A  Answered on 5/25/2018 by InyoPools Product Specialist Patrick P.

Hi Jackie, If your motor has a foot base on it like then you will need the BN25 motor and if your motor does not have a foot base on it then you will need the PL1131 1 HP Replacement Motor
 Reply


?     Asked on 5/31/2018by Rhett J. Brown

What would be the right replacement for part 7 182716-24 hp 3/4 spl?
 Reply

A  Answered on 5/31/2018 by InyoPools Product Specialist Hector F.

The correct replacement motor would be the part number BN23V1
 Reply


?     Asked on 6/3/2018by Steven Smith

Will this motor work as a replacement for an Aquatools AT2310131?
 Reply

A  Answered on 6/5/2018 by InyoPools Product Specialist Lennox H.

Hi, Steven. I was not able to use the model number provided to confirm if the motor will fit. Please provide pictures of the pump and motor label. 
 Reply


?     Asked on 6/15/2018by Conrad Hernandez

Trying to replace a sta-rite motor model no: ABG4E7-2A4SP 12 amp 3 prong, no twist cord. 120v
 Reply

A  Answered on 6/16/2018 by InyoPools Product Specialist Lennox H.

Hi, Conrad. This BN25V1 Motor is a substituted replacement for the ABG4E7-2A4SP model pump. Other replacement parts for your model pump are listed on the Sta-Rite ABG Series Parts Diagram.
 Reply


?     Asked on 6/26/2018by David

I am looking for a replacement pump for my Jacuzzi CFR 50 pool filter (above ground) the label on the current pump says Part 7 - 186532 - 22, the make seems to be "Magnetek" I am hoping to find a direct replacement? Do you think this pump will work?
 Reply

A  Answered on 6/26/2018 by InyoPools Product Specialist Hector F.

Yes, this would be the correct replacement motor for your model 7-186532-22 motor. 
 Reply


?     Asked on 7/4/2018by JAMES

I AM LOOKING TO REPLACE THE STA-RITE JWPA5E7L-2A2 MOTOR. WOULD THIS MOTOR DO SO?
 Reply

A  Answered on 7/4/2018 by InyoPools Product Specialist Alex V.

James, Yes, this motor will replace your existing one. 
 Reply


?     Asked on 7/7/2018by Linda

I am looking fo a replacement for pool sta-rite pump model no: JWPA5EL-2A Motor Model S48874A03. HP 1.0. On a sta-rite system 3 (15 years old). Will I need a seal kit? Please assist.
 Reply

A  Answered on 7/8/2018 by InyoPools Product Specialist Alex V.

Linda, Aside from the BN25 motor, we recommend getting the 1HP/1.5HP seal kit as well. 
 Reply


?     Asked on 7/9/2018by Bill

What pump can be used to replace a Jacuzzi (Magnetek) 1HP SPL, Part 7-186532-22, 115V, 3450 RPM, FRV48Y pool pump
 Reply

A  Answered on 7/9/2018 by InyoPools Product Specialist Hector F.

This is the correct motor for the model 186532 motor. 
 Reply


?     Asked on 8/5/2018by Inyo Visitor

I need to replace my motor it's a Sta-rite model #ABG4E7-2A4. will this motor be able to replace it with out any extar parts needed?
 Reply

A  Answered on 8/5/2018 by InyoPools Product Specialist Hector F.

I would recommend replacing keys number 4 and 5 on the parts diagram here
 Reply


?     Asked on 8/12/2018by Inyo Visitor

does the thru bolts come with this motor if not can I get a part number
 Reply

A  Answered on 8/12/2018 by InyoPools Product Specialist Lennox H.

Hi. Yes, new thru-bolts are included with the motor.
 Reply


?     Asked on 9/3/2018by Mike

Is this the correct replacement motor for Century Pool/A.O.Smith part no. 0-193262-10 ?
 Reply

A  Answered on 9/6/2018 by InyoPools Product Specialist Hector F.

Yes, this would be the correct motor replacement for your motor. 
 Reply


?     Asked on 11/6/2018by Inyo Visitor

if i turn the shaft will this motor put out electricity.
 Reply

A  Answered on 11/6/2018 by InyoPools Product Specialist Hector F.

No these motors do not generate electricity. 
 Reply


?     Asked on 1/19/2019by Eric

Is this a cross with part# 7-184307-23?

 Reply

A  Answered on 1/21/2019 by InyoPools Product Specialist Michelle B.

Hello, Yes, that will be a compatible motor for part number 7-184307-23.
 Reply


?     Asked on 1/19/2019by Eric

Is this a cross with part# 7-184307-23?

 Reply

A  Answered on 1/20/2019 by InyoPools Product Specialist Kevin G.

Hello, yes this will work for you.
 Reply


?     Asked on 3/6/2019by Tina

I have a dynamo 1 hp motor, part no. 340197. Do you have a replace?
 Reply

A  Answered on 3/6/2019 by InyoPools Product Specialist Ronald E.

Hello,Yes we the motor for that pump it is the A.O. Smith 1 HP Thru-Bolt 48Y Motor - BN25V1.If you are referring to the pump itself the Dynamo Pump 1 HP w/ STD Cord - 340197 we have that in stock too.
 Reply


?     Asked on 4/4/2019by Hayward power-flo LX 1hp replacement

is this a direct replacement for Hayward Power-Flo LX 1hp pump part number O-187872-21

 Reply

A  Answered on 4/4/2019 by InyoPools Product Specialist Lennox H.

Hi. This BN25V1 motor is the correct replacement. 
 Reply


?     Asked on 4/10/2019by Michael Mejia

What is the GPM for this 1HP and 1.5 HP motor?
 Reply

A  Answered on 4/12/2019 by InyoPools Product Specialist Lennox H.

Hi. Michael. Flow rates are calculated based on the pump's wet end and Total Dynamic Head (TDH), not the motor only. 
 Reply


?     Asked on 4/28/2019by Beth

I have a green, blue and white wire. Green being the ground, where do the blue and white wire go for the BN25V1?
 Reply

A  Answered on 4/29/2019 by InyoPools Product Specialist Lennox H.

Hi, Beth. You will need to use a multi-meter to determine which wire is the line (115V) and which one is neutral. The line wire will go to Terminal 1, neutral, Terminal 6 then connect the ground. 
 Reply

  • Commented on 4/29/2019 by Product Owner

    I did that......nothing. I'm on 2 40amp breakers for the whole pool. GFCI plug has been replaced. I got someone coming out Wednesday . I will take pics and update on the problem. Thanks.
     Reply

    • Commented on 5/6/2019 by InyoPools Product Specialist Patrick P.

      Thanks, Beth keep us posted we are interested to see what you find out.
       Reply


?     Asked on 5/19/2019by Jeff B

Hi I am on my 3 rd motor in 8 pool seasons I love the motor but in the corrosive environment of the pool and the out doors the housing and motor mounting plate continues to deteriorate since it is made from powder coated steel. I'm interested in purchasing a motor with a stainless steel housing. I realize it will cost $$ but in the long run it will cost less then replacing the motor every 3 to 4 years. Can you respond with a part # of a motor with a SST motor housing / mounting plate? Mod#193262
 Reply

A  Answered on 5/20/2019 by InyoPools Product Specialist Patrick P.

Hi Jeff, Unfortunately this motor or any of the motors we carry are offered in a stainless steel housing. We would suggest replacing your shaft seal with a heavy duty shaft seal. Could you send us a few photos of your pump including a wide shot showing where the pipes go in and out of the pump? To send the photos simply click on the reply link below to upload your photos. You may also consider a Protective Motor Cover.
 Reply


?     Asked on 6/3/2019by Thomas

I am looking for a replacement motor for a A.O.Smith model S48L2A6A8 Ser#8B99 1HP .75KW 115V RPM3450 13.8AMPS There is also a# SP1510-Z1-XE . Is the BN25V1 a replacement for this motor?
 Reply

A  Answered on 6/13/2019 by InyoPools Product Specialist Steve M.

Thomas, yes, the A.O. Smith 1 HP Thru-Bolt 48Y Motor - BN25V1 will be the direct replacement for your S48L2A6A8 motor.. 
 Reply


?     Asked on 6/3/2019by Betty

Can you please tell me if this motor will work with a Proline 1 1/2 hp motor 7-193868-24. A.D. Smith. Thank you!

 Reply

A  Answered on 6/3/2019 by InyoPools Product Specialist Lennox H.

Hi, Betty. Yes, this BN25V1 is the correct replacement motor. 
 Reply


?     Asked on 6/20/2019by Jason

For the BS25 do you sell any internal parts. Like the armature?? If so how much would that be
 Reply

A  Answered on 6/21/2019 by InyoPools Product Specialist Lennox H.

Hi, Jason. We do sell some replacement parts, however, not the armature. 
 Reply


?     Asked on 6/21/2019by Dan

I have a Pentair Opti-Flo pump, part number 347988SR, with A.O. Smith motor # 193262 (1.00 HP, 3450 RPM, 12.0 MaxAmps). I need a replacement motor. Will the BN25V1 motor work for me? Thanks.
 Reply

A  Answered on 6/25/2019 by InyoPools Product Specialist Kevin G.

Yes, this motor will work for you. In addition to the motor, you will also need to replace your old shaft seal with part 5250-104.
 Reply


?     Asked on 7/6/2019by Richard Bartley

What do I need to replace the Century 7-177760-23? Seals? Switches? Cord?
 Reply

A  Answered on 7/8/2019 by InyoPools Product Specialist Joe S.

Hello Richard, based on 7-177760-23 the A.O. Smith 1 HP Thru-Bolt 48Y Motor - BN25V1 would be the correct motor. The cord needed would be 3-Prong Pump Power Cord, 6', 14 GA, 115V - SPX1250WA. And for the seals Finding the Tune Up Kit for Your Pool Pump.
 Reply


?     Asked on 8/3/2019by bob

what is the expected life for a above ground pump motor. sta-rite 1 hp?
 Reply

A  Answered on 8/5/2019 by InyoPools Product Specialist Matt S.

A pool pump motor should be expected to last 2-4 years.
 Reply


?     Asked on 8/9/2019by Alex

i have a speck E90-I pump 7-193530-20 what motor would i need to replace this with
 Reply

A  Answered on 9/23/2019 by InyoPools Product Specialist Michelle B.

Correct replacement is BN25V1 , A.O. Smith 1 HP Thru-Bolt 48Y Motor - BN25V1 (35-126-1010)
 Reply


A  Answered on 9/30/2019 by Industry Professional

yes, and make sure to order a new pump seal 5143-130, and casing "O" ring 5143-130
 Reply


A  Answered on 9/20/2019 by Industry Professional

Correct replacement is BN25V1 , A.O. Smith 1 HP Thru-Bolt 48Y Motor - BN25V1 (35-126-1010)
 Reply


?     Asked on 8/12/2019by Inyo Visitor

Need a replacement motor and not sure which one to get

 Reply

A  Answered on 8/12/2019 by InyoPools Product Specialist Jessica C.

Hi, The replacement motor you will need based on the motor label in the picture you provided will be the Waterway Motor Thru Bolt .75hp 115v - Ss Shaft (bn24ss)
 Reply


?     Asked on 8/14/2019by Inyo Visitor

Hello. May need a replacement motor. Current part number is 7-177760-23. Pool size is 16 x 32. Current hp is 1.5. What can you recommend?
 Reply

A  Answered on 8/14/2019 by InyoPools Product Specialist Lennox H.

Hi. This BN25V1 motor is the correct replacement for P/N 7-177760-23. Some above ground pool pumps have an operational and performance HP rating. 
 Reply


?     Asked on 8/27/2019by AnnaMaria

Hi there, I often find myself trying to find a replacement pump/motor for the Sta-rite LT 1/6hp, 115v, 1-Spd - LT1/6L. I understand that it has been discontinued, but I have not yet been able to find ANY volute/wet end that would discharge on the same side, and thus make it to so that ym customer does NOT have to change his plumbing around. I believe the volute has been discontinued, but does noone make a compatible one? Please help me if you can. AM

 Reply

A  Answered on 9/20/2019 by Industry Professional

The Gecko Alliance Circmaster 1/5 HP - 02593000-2010 and see if you can make plumbing changes to make it work for your application.
 Reply


A  Answered on 9/20/2019 by Industry Professional

34-402-1144 Best match - will require one plumbing change to either suction or discharge of approximately 1 1/2 inches and new unions installed that come with the pump. Gecko Alliance Circmaster Cmcp, 1/15 Hp, 115 V (02593000-2010)
 Reply


?     Asked on 9/4/2019by DB

I think my Sta Rite JWPA 5E7L -2A2 motor has seen better days. Would the 25BN be the correct replacement? Photo included.

 Reply

A  Answered on 9/4/2019 by InyoPools Product Specialist Lennox H.

Hi, DB. Yes, this BN25V1 motor is the correct replacement. You will also need to get the Sta-Rite JWPA Seal Kit 1 & 1-1/2 HP - APCK1187
 Reply


?     Asked on 9/7/2019by jesus benitez

hello i have a jacuzzi eclipse with bump model S55CXNPH-7241 , i dont see capacitor for start , maybe dont use , but now the motor dont start , have the noise bummmmmm , what motor i can buy , thanks

 Reply

A  Answered on 9/12/2019 by InyoPools Product Specialist Hector F.

This BN25 is the correct replacement motor. 
 Reply


?     Asked on 9/8/2019by Gerry Breen

I have an A.O. Smith HP 1.0 SPL from the Splash Pak series. Part # is: 7-187610-21 Type is: SP FRW48Y What is the correct replacement motor? What gasket seal parts do I need?
 Reply

A  Answered on 9/10/2019 by InyoPools Product Specialist Joe S.

Yes, based on the information provided the A.O. Smith 1 HP Thru-Bolt 48Y Motor - BN25V1 would be correct. Confirm also with HP and SF on label.
 Reply


?     Asked on 9/17/2019by Earl T Thornton

My current TDH is 46 with a 1.5 hp motor with a sf of 1.47. Will this be a suitable replacement
 Reply

A  Answered on 9/18/2019 by InyoPools Product Specialist Lennox H.

Hi, Earl. Unfortunately, we will need the Frame (FR) specs in order to locate the correct replacement. This motor does not match the SF rating provided.
 Reply


?     Asked on 12/6/2019by LARRY

I have a bathtub jacuzzi and the pump seal is leaking The part number is 9-159964-55 which comes up on your website. the problem is the motor is mounted vertical, and it is about 20 years old., Will the one you have replace it? I am going to try to have the pump seal replaced because the pump still works.

 Reply

A  Answered on 12/9/2019 by InyoPools Product Specialist Lennox H.

Hi, Larry. This BN25V1 motor is a suitable replacement. The replacement Pump Shaft Seal - PS-200 and Volute O-ring - 92200090 are also available. 
 Reply


?     Asked on 1/21/2020by Juan Canache

What motor would be the replacement for a Century 7-1930004-20 Frame: W48Y 230/115 Volts 1HP
 Reply

A  Answered on 1/22/2020 by InyoPools Product Specialist Lennox H.

Hi, Juan. This motor will NOT work as a replacement because of the built-in stand. 
 Reply


?     Asked on 2/7/2020by Jerry

I have a Hayward pool pump that was squealing and finally gave up. It has an AC Smith 1.0 HP motor with a Q-1878SP 1510ZXBC FR#R48Y, Part # 187872-21. I'll attach a photo. Looking to replace the motor, I'm guessing. Wanted to see if the pump motor I'm looking at is the correct one. Thanks, Jerry

 Reply

A  Answered on 2/11/2020 by InyoPools Product Specialist Lennox H.

Hi, Jerry. This BN25V1 is the correct replacement motor. 
 Reply


?     Asked on 3/7/2020by david

I need a replacement motor for pentair 1hp 115v 60hz 1ph kvw 3450 rpm sf1.oo max amps120 model no.dyn11-n1 part no.1/340197 motor with pump like your picture of PENTAIR/PAC FAB DYNAMO
 Reply

A  Answered on 3/7/2020 by InyoPools Product Specialist Patrick P.

Hi Bryan, Yes this is the correct replacement motor for your Pentair Pac-Fab Dynamo dyn11-n1 part no.1/340197. You will also need a Dynamo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply

  • Commented on 3/7/2020 by Product Owner

    I need the motor and pump like the one shown, pentair/pacfab dynamo with electrical hookup,
     Reply


?     Asked on 4/17/2020by Thomas Liucci

I need to replace my starite motor. older model#S48B74A03 1HP 115volt 12amps can u please help me with ordering the right motor?
 Reply

A  Answered on 12/7/2020 by InyoPools Product Specialist Megan C.

The Century 1.0 HP Thru-Bolt 48Y Motor - BN25V1 can be used to replace the S48B74A03. The pump seal will need replaced when replacing the motor, please see How To Find The Correct Pool Pump Shaft Seal http://www.inyopools.com/blog/how-to-find-the-correct-pool-pump-shaft-seal/ 
 Reply


?     Asked on 4/17/2020by Thomas Liucci

what is your return policy on the pool motors above ground
 Reply

A  Answered on 11/6/2020 by InyoPools Product Specialist Hector F.

Hi Thomas, generally our return policy is that the item must be in new and unused condition with the original packaging within 30 business days. Please see our return policy for further details. 
 Reply


?     Asked on 4/27/2020by Todd Burger

Will this motor replace the 1HP Sta-Rite model number JWPA5E7L-2A1??
 Reply

A  Answered on 4/27/2020 by InyoPools Product Specialist Patrick P.

Hi Todd, Yes this is the correct replacement motor for the JWPA5E7L-2A1 you will also need JWPA seal kit
 Reply


?     Asked on 5/2/2020by Fred A. Jones

I have an A.O. Smith motor that needs replaced. I believe the model # is SP1510-Z-1-XES Serial # BY04-28 FR W48Y RPM 3450 Thanks

 Reply

A  Answered on 1/8/2021 by InyoPools Product Specialist Hector F.

Yes, this is the correct replacement motor for the motor included in your photo. You will also need a Hayward PowerFlo LX shaft seal when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 5/5/2020by Frank Tenuto

Does this pump come with the power cord? If so, how long and is it a standard plug or twist lock plug? Thank you.
 Reply

A  Answered on 5/5/2020 by InyoPools Product Specialist Patrick P.

Hi Frank, No this motor does not come with the 3 prong cord with plug, the majority of customers will remove the cord from their old motor and use on their new motor. We do carry a 3 Prong Pool Motor Cord here. If you need a Twist Lock Cord we carry one here Twist Lock Cord
 Reply


?     Asked on 5/6/2020by Lori

I am looking for a replacement motor for a Century 1 HP, 3450 RPM, 115 Volts part #7-186533-22. Is this the correct replacement motor?
 Reply

A  Answered on 12/8/2020 by InyoPools Product Specialist Hector F.

Hi Lori, the correct replacement motor for your motor part number 186533 is the BN24. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
 Reply


?     Asked on 5/24/2020by stan

will this replace a jwpa5e7l-2a2 sta-rite motor
 Reply

A  Answered on 5/25/2020 by InyoPools Product Specialist Patrick P.

Yes this is the correct replacement motor for the jwpa5e7l-2a2 sta-rite you will also require this JWPA 1 HP Seal Kit
 Reply


?     Asked on 5/31/2020by Inyo Visitor

Does this motor go with the Hayward SP1592 pump?
 Reply

A  Answered on 6/9/2020 by InyoPools Product Specialist Hector F.

Yes, this motor is a compatible replacement motor for the model Hayward SP1592 pool pump. 
 Reply


?     Asked on 6/2/2020by Diane

I have an above ground 15 foot pool with a Hayward filter model #C4001575XES The pump is 1 HP SP1510Z1XBC Part -187872-21 (60 GPM) 115 Volts 11.0 Amps The motor is shot. Is this the replacement for it. I'm so confused. Thank you. 201-370-2428
 Reply

A  Answered on 6/10/2020 by InyoPools Product Specialist Hector F.

Yes, this would be the correct replacement motor for your part number 187872 motor. 
 Reply


?     Asked on 6/3/2020by Denis Fuentes

Hi I’m trying to replace a pool motor on a above ground pool. Here’s the MOD# S48B74A03 1 1/2 HP Which of this two motors fits my BN25V1 (1hp) or BN35V1 (11/2) here’s the picture for better information. Thank you Respectfully

 Reply

A  Answered on 6/4/2020 by InyoPools Product Specialist Hector F.

Your direct single speed replacement motor will be the BN35V1 that you can view by clicking here
 Reply


?     Asked on 6/8/2020by Kyle Schwendiman

Looking for everything I need to replace this motor see below. Motor went and need replacement ASAP. If you could please help me if this is the correct motor and all the parts I will need including the on/off switch

 Reply

A  Answered on 6/8/2020 by InyoPools Product Specialist Patrick P.

Hi Kyle, You will require this BN25 1 HP Motor and this Hayward Power Flo Matrix Seal Kit
 Reply


?     Asked on 7/10/2020by Inyo Visitor

Hi, I need a replacement motor that is in the pictures. The motor says AO Smith 193530 and has HP1.5SPL stamped on it. Do I need the 1 HP (BN25V1) or 1.5 HP(BN35V1). or something completely different? It was a little unclear because the HP on the sticker is blank, but has the other stamped number. Thank you!

 Reply

A  Answered on 12/14/2020 by InyoPools Product Specialist Hector F.

Hi, yes this is the correct replacement motor for your motor. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
 Reply


?     Asked on 7/13/2020by william b lamar

how does it install to the rest of the filter easy or not
 Reply

A  Answered on 11/18/2020 by InyoPools Product Specialist Hector F.

Hi William, here is a general guide that we created called "How to Replace an Above Ground Pool Pump Motor" that should assist. 
 Reply


?     Asked on 7/21/2020by Replacing Motor

Hello I am looking to replace my MagneTek 1081/1795 Pump Duty. Part # 7-177961-23 1 HP 115 VOLTS RPM 3450
 Reply

A  Answered on 7/21/2020 by InyoPools Product Specialist Hector F.

This motor model BN25 is the correct replacement motor for your motor part number 177961. 
 Reply


?     Asked on 8/13/2020by Cason

What size start and run capacitors are on my magnetek part- 7-177961-23 motor?
 Reply

A  Answered on 8/13/2020 by InyoPools Product Specialist Lennox H.

Hi, Cason. This specific model motor does not have a start or run capacitor. 
 Reply


?     Asked on 10/10/2020by Gordon

I have a Pentair dynamax 340219 2hp pool pump and I need to reduce the size if it to a 1hp. Will this just be a direct swap out? Thank you
 Reply

A  Answered on 10/14/2020 by InyoPools Product Specialist Hector F.

Yes, that is correct however you will also need to replace the impeller and diffuser bracket that need to be rated for 1 hp as well. You can view those parts on this Pentair Dynamo Pump parts diagram by clicking here
 Reply


?     Asked on 11/16/2020by Inyo Visitor

Hi there, can this pump be used in lieu of Part 7 182718-40 / E44549 LR94643, by Century Pool 12v / 1.5 hp / 115 V / 3450 RPM
 Reply

A  Answered on 11/17/2020 by InyoPools Product Specialist Joe S.

Hello, thank you for contacting INYO POOLS. We would recommend the Century 1.5 HP Thru-Bolt 48Y Motor - BN35V1 as the correct replacement.
 Reply


?     Asked on 5/3/2021by Mike

Will this work for my motor

 Reply

A  Answered on 5/3/2021 by InyoPools Product Specialist Danny R.

Hey Mike,Yes the BN25 pool pump motor is the correct replacement for your Pentair 347982 Optiflo Pump.  
 Reply


?     Asked on 5/5/2021by Lisa

Hello, I have a Sta-Rite pool filter and currently have the BN25SS pool pump that needs replaced. I have been told that pump motor has been discontinued. Will the BN25V1 motor here on your site work properly/be a compatible fit?

 Reply

A  Answered on 5/5/2021 by InyoPools Product Specialist Danny R.

I do not recommend replacing the BN25SS motor with this motor.  The recommended pool pump motor for the BN25SS is PART # 5268-03
 Reply


?     Asked on 5/11/2021by Steve Weissman

My pump just dies. Can I use this motor? P

 Reply

A  Answered on 5/11/2021 by InyoPools Product Specialist Patrick P.

Hi Steve, Yes this is the correct replacement motor for your pump. We would also suggest this Power Flo LX Shaft Seal when replacing your motor.
 Reply


?     Asked on 5/17/2021by Sherri J Pearce

I have a Sta-Rite JWPA5EC-2A3U 1 HP POOL PUMP. It has quit working. Which motor do I need to use and which shaft seal? Please advise asap.

 Reply

A  Answered on 5/17/2021 by InyoPools Product Specialist Danny R.

The BN25 is the correct motor for the Sta-Rite JWPA5EC-2A3U 1 HP Pump.  Here is the link to the shaft seal for this pump.Pump Shaft Seal 3/4", PS-201
 Reply


?     Asked on 5/31/2021by Inyo Visitor

Is there a warranty and how may years is it?
 Reply

A  Answered on 5/31/2021 by InyoPools Product Specialist Patrick P.

Yes this motor comes with a 1 year warranty.
 Reply


A  Answered on 6/1/2021 by Product Owner

The on/off switch broke off my Pentair 1 HP motor. Can the switch be replaced or do I need to purchase a new motor? Do you carry the Pentair motor and how much is it and what is the warranty on it?
 Reply

  • Commented on 6/2/2021 by InyoPools Product Specialist Patrick P.

    Hi Arthur, **NOTE THIS MOTOR IS SHIPPED LESS ON/OFF SWITCH. YOU MAY PURCHASE THE ON/OFF SWITCH SEPARATELY BY ORDERING PART # 18374501.** We currently have 1 of these switches in stock, so I would suggest ordering sooner than later =)
     Reply


?     Asked on 6/15/2021by Josh Pindell

I have a Dynamo Pump that is not working. Motor # 193262 P/N 340210 Will this work looks like HP is different
 Reply

A  Answered on 6/15/2021 by InyoPools Product Specialist Patrick P.

Hi Josh, Yes this is the correct replacement motor for the 193262 motor. You will also require this Dynamo Shaft Seal when replacing your motor. Here is a Video on How to Replace an Above Ground Pool Pump Motor which you may find helpful when you tackle this project. 
 Reply


?     Asked on 6/21/2021by Kim Baade

Hi! I currently have a Century 7-186533-22 motor that has seized. Will the BN25V1 bolt up correctly to the skimmer that I have? I can't see the same cover on the new one vs the cover on mine to compare the bolt pattern. Thank you!

 Reply

A  Answered on 6/22/2021 by InyoPools Product Specialist Danny R.

I am showing the proper replacement motor for your 7-186533-22 to be the Century 3/4 HP Thru-Bolt 48Y Motor - BN24V1This motor will fit with the rest of your pool pump.
 Reply


?     Asked on 6/30/2021by ROBERTO

Hi... Will this work for my pump?

 Reply

A  Answered on 7/2/2021 by InyoPools Product Specialist Robert M.

The correct replacement motor for your 7-186533-22 is model BN24.
 Reply


?     Asked on 8/5/2021by Herbert Timm

I have a sta-rite pump motor # s48b74a03 and model # is jwpa5e7l-2a-1 want to make sure I'm ordering the correct part.
 Reply

A  Answered on 8/5/2021 by InyoPools Product Specialist Robert M.

Yes, the BN25 is the correct motor replacement for model s48b74a03.
 Reply


?     Asked on 8/10/2021by Inyo Visitor

i have a magnetek pool pump motor part # 7-177760-23 1.5 h.p. what do i need for a replacement motor?
 Reply

A  Answered on 4/20/2022 by InyoPools Product Specialist Joe S.

Good day, based on the number provided you would need to order the Century 1.5 HP Thru-Bolt 48Y Motor - BN35V1.
 Reply


?     Asked on 8/16/2021by Joey J

You recommend the BN24V1 motor for a replacement of my current SP1540Z1E. My question is, will the BN24V1 bolt up to my SPX1500AA pump housing without any issues? What I am attempting to do is assemble a complete filtration system with parts I have on hand. The parts consist of a Hayward EC30, a shot SP1450 motor, (to be replaced) and a SPX1500AA pump. Thanks
 Reply

A  Answered on 8/17/2021 by InyoPools Product Specialist Craig C.

Hello Joey.  The Magnetek Century Motor model BN25V1 is a compatible replacement motor for the Hayward Power-Flo 1500 Series Pumps.  The BN25 motor can be installed with no adjustment required to the Power-Flo Pump.  The GOKIT12 will provide the seals and o-rings recommended to complete this project.    Tune Up Kit Power-Flo 1500 Series - GOKIT12
 Reply


?     Asked on 8/21/2021by Carmen Venable

MY AO Smith pool pump motor died. What it the replacement motor I need?

 Reply

A  Answered on 11/9/2021 by InyoPools Product Specialist Stephen B.

Thank you for contacting Inyo Pools, Century 1.0 HP Thru-Bolt 48Y Motor - BN25V1 is the correct replacement motor.
 Reply


?     Asked on 9/17/2021by George Esqueda

Do you carry a replacement above-ground pool pump motor as shown on the attached pics? Thanks

 Reply

A  Answered on 9/17/2021 by InyoPools Product Specialist Craig C.

Hello George  The Magnetek Century 1.0 Thru-Bolt Motor model BN25V1 is the direct replacement for the motor identified in the photo provided, your model S48AA11A79.  Century 1.0 HP Thru-Bolt 48Y Motor - BN25V1  It is recommended that the motor shaft seal, Faceplate Cover o-ring, and diffuser o-ring be replaced concurrent with the new motor.  Pump Shaft Seal 5/8" - PSR-200     Volute Cover O-ring - 805-0253      O-ring (805-0330)
 Reply


?     Asked on 2/10/2022by Boone

is this the correct pump to replace my burnt up pump.

 Reply

A  Answered on 2/10/2022 by InyoPools Product Specialist Rich N.

Yes, the Century 1.0 HP Thru-Bolt 48Y Motor - BN25V1 is the correct motor for your pump. The amps confirm it, since the manufacturer put 1.5SPL horsepower on the label, which is not a standard term for anything.  We recommend replacing the motor shaft seal when replacing the motor to ensure a leak-free installation.  
 Reply


?     Asked on 4/1/2022by Kathy

What motor do I need to replace this Hayward Power Flo LX pump? 1HP SP1510Z1XBC Thank you

 Reply

A  Answered on 4/1/2022 by InyoPools Product Specialist Rich N.

Hi Kathy, the BN25V1 motor is the perfect replacement for the one in the picture.  We do not have a Tune-Up Kit for your Hayward Power-Flo LX pump, so we recommend purchasing a new motor shaft seal and a new housing o-ring for a leak-free installation.  
 Reply


?     Asked on 9/30/2022by Mikr

My century motor looks nothing like the one pictured but has the same part number. Do you have the one in the picture below? Thanks

 Reply

A  Answered on 10/1/2022 by InyoPools Product Specialist Hector F.

Hello, Century has acquired a few manufacturers and have used multiple designs however the direct replacement for your specific motor model is the BN24
 Reply


?     Asked on 1/11/2023by Mike

Hi - I have a Century 7-193004-20, s/n 04415J2, dual voltage 115/230 with an Aquatechnix PES90-11 housing. The BN25V1 is 115v. What motor is compatible?

 Reply

A  Answered on 1/20/2023 by InyoPools Product Specialist Rich N.

Hi Mike, the BN25 motor will not work for your pump (the mounting flange will get in the way), and the original motor has been discontinued by the manufacturer.  The best option for you is this BV91 motor.  Since this is a 115-volt motor, remove the additional power wire if you are using 220 volts and replace the breaker with a single-pole breaker.  We also recommend replacing the shaft seal and the casing o-ring when you replace the motor.  
 Reply


?     Asked on 9/14/2023by Russell Suess

Is this the correct motor to replace my waterway 1hp motor. See pics.

 Reply

A  Answered on 9/14/2023 by InyoPools Product Specialist Jacob F.

Hello, yes, the BN24 is the correct replacement for your current motor. 
 Reply