$7.76

Qty:

By U.S. Seal Manufacturing


Details

Top

Part # 5250-106

Manufacturer Code PS-1000

Dimensions 0.8" X 1.25"

Alternate Part #'s 001438L, 004380, 01512-101, 01512101, 04380, 04547, 07-1734S, 071734, 111-0293, 1128-1006, 11281006, 1128106, 16070200B, 300-009, 300009, 301007, 304-D, 306-1002, 3061002, 31-813, 310-108, 31813, 319-3100B, 319-3110B, 3193100B, 3193110B, 3262-04, 35-100-1028, 35-423-1048, 35-426-1060US, 354231060, 397012, 39701200, 397020, 39702000, 60-828-813, 603240, 606640, 71734, 811-1001, 8111001AB, 92500050, 92509040, AF-14, AMP1018591, AP-304D, AP304D, AQF1017737, AS-1000, AS1000, LA1000, LLA1000, P SEAL 5, P-19-0, P-28050, P-28323, P-55, P28323, P55, PRE1018422, PS-1000, PS1000, PSEAL5, PSR-1000, PUR1016168, PVP55, STA1015156, U109-136SS, U109136SS, VG-1000, VG1000, 35-423-1060, APCAS1000, PSR1000, USSPS1000

Product Description

This is a generic pump motor shaft seal for many different pool pumps.  Some of the more common pumps it is used on include the Pentair WhisperFlo, Polaris PB460 booster pump, American Products Ultra Flo, Astral Astra Max and Waterway Workman.  There are many other makes and models listed under the "Parts" tab above.

This seal is also available in a heavy duty version PS3865 for pools with salt chlorine systems or ozonators.

Frequently Bought with Shaft Seals

Clear RTV Silicone 6558-0

Top

?     Asked on 2/16/2012by Guest

I just finished replacing the shaft seal on my booster pump. As soon as I turned the pump on water was leaking from the shaft seal. Is it defective or am I doing something wrong?
 Reply

A  Answered on 2/16/2012 by InyoPools Product Specialist Patrick P.

Depending on the model, the installation of a booster pump shaft seal can be slightly different than a pool pump shaft seal. Some booster pump and pool pump shaft seals require that a silicone sealant be used on the outer areas of the metal seat of the shaft seal. The seal will need to be lightly hammered into the body of the pump. You can use a 1 inch PVC coupling or a piece of 1 1/4 inch PVC pipe and a rubber mallet. This procedure will apply to any pool pump or booster pump using a >PS-1000 style shaft seal.
 Reply


?     Asked on 9/24/2014by Guest

What is the size of this shaft seal?
 Reply

A  Answered on 9/24/2014 by InyoPools Product Specialist Patrick P.

The shaft seal is listed as at 5/8".
 Reply


?     Asked on 3/13/2015by clay

Will the shaft seal 5250-106 fit on a waterway pump pb2250 6p?
 Reply

A  Answered on 3/13/2015 by InyoPools Product Specialist Wes B.

Yes, That is the correct seal for your pump.
 Reply


?     Asked on 5/19/2015by claudio

can u let me know how to change seal
 Reply

A  Answered on 5/20/2015 by InyoPools Product Specialist Patrick P.

Hi Claudio, Here is a Video We Created on How to Replace a Shaft Seal which goes over this quiet well.
 Reply


?     Asked on 12/28/2015by Brian

I am looking for a seal for a American ultra flow pool pump. their part number is 397012 and is a seal #1000. is your part the same
 Reply

A  Answered on 12/28/2015 by InyoPools Product Specialist Andy O.

Hello Brian- The Seal, Pump 1000 (psr 1000) part number 5250-106 would be the same seal and will fit on the Ultra Flow.
 Reply


Top
Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver, Socket Set, Adjustable Wrench

Leaking seal

Written on 5/3/2022 by Guest

Followed instructions on the video tutorial.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Nut Drivers, Socket Set, Wrench Set, Adjustable Wrench, RTV Silicone

1     0

Ceramic seal leaking--they all will from time to time...

Written on 12/4/2021 by Guest

Shut off power. Removed 4 bolts holding pump and motor together. Disassembled impeller, diffuser and pump face. removed old seal, installed new seal parts - metal half into pump face (used gasket silicone before pressing in metal component), and new rubber/ceramic component into impeller. Re-assembled pump/motor and fired it up! No leaks!

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver, Pliers, Socket Set, Wrench Set

Leak in the seal of my booster pump

Written on 7/18/2020 by Guest

I ordered a new seal kit from INYO pools. When it arrived I used the video from You Tube on the INYO website to remove the cover, volute, and impeller. It was easy to replace the seals and reassemble the parts following the INYO video. New seals no longer leak.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Pliers, Socket Set, Wrench Set

1     0

Replaced seals while replacing the motor

Written on 8/13/2019 by Guest

Because my pump has been there 10 years I had to watch a YouTube video to assist me in getting the wet end of the pump off the motor shaft. I removed the long bolts from the back of the motor and used a rubber mallet to remove the motor back cover. Placing the pump in a vice I hit the motor shaft with a hammer and knocked it out. Then I could use simple hand tools to remove the impeller. I used pliers to remove old seal. Cleaned the housing and install the seals. Then I assembled the pump with the new motor.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Pliers, Socket Set, Wrench Set

Replaced seals while replacing the motor

Written on 8/13/2019 by Guest

Because my pump has been there 10 years I had to watch a YouTube video to assist me in getting the wet end of the pump off the motor shaft. I removed the long bolts from the back of the motor and used a rubber mallet to remove the motor back cover. Placing the pump in a vice I hit the motor shaft with a hammer and knocked it out. Then I could use simple hand tools to remove the impeller. I used pliers to remove old seal. Cleaned the housing and install the seals. Then I assembled the pump with the new motor.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Socket Set, Wrench Set, Adjustable Wrench

noise , loud!!

Written on 7/26/2017 by Guest

after breaking a perfectly good impeller [ didn't have a good strap wrench], I found an electric motor repair shop in our little town and he knew the correct bearing no. for a 1 hp century motor. It was quite easy to install , push out the old [ note there is a screw retainer to remove first. then gently tap in the new bearing [was $8] . noise gone ! Note: when you reassemble the pump after replacing the impeller be carful not to over tighten the 2 little stainless steel screws or they will pull out of the plastic. - Pentair whisperflow pump-

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

one inch pvc union

1     0

If after you install the new pump seal, the pump won't move water, you put the metal side of it in backwards.

Written on 7/11/2017 by Guest

The metal part of the pump seal will fit into the body of the pump from either direction, but it only works if installed in the right direction. Make sure you push it into the side of the pump seal that has a little indentation that matches the lip of the metal rim to the seal. Very easy to do it wrong.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.74  out of 5 stars)
61 Rating
5 star:
 
(50)
4 star:
 
(7)
3 star:
 
(3)
2 star:
 
(1)
1 star:
 
(0)

The Most Recent Reviews








































Top